breeeze / rpos Goto Github PK

I use VLC or some DVR (for example https://geniusvision.net/ ) test on your software and I see that the quality isn't good, sometimes video is delayed.
I tested with another rtsp on PI https://github.com/mpromonet/h264_v4l2_rtspserver
with video 720/1280 (15 to 30fps) it seems better (no delay)
I suggest that maybe you should switch to this library or do you have any idea?
(In my opinion, you called execution file from nodejs)
I'm researching a library support RTSP, ONVIF, discovery for Raspberry to build a smart camera from Pi, the final target is integrating Raspberry smart camera to any DVRs or NVRs.
I hope get some advises from you.
Regards
Bao

Hello, I believe I have everything installed correctly after having issues with node. I load the camera driver per instructions and run rpos.js. I cannot connect to the interface using 127.0.01:8081 or 192.168.1.xx on a different computer on the network. I really can't confirm that the service is running, not sure how to. Is there a step i'm missing here?

While using rpos, I noticed that when setting video_bitrate through the web interface, the value is not preserved. The value always reads '0' in the v4l2ctl.json settings file. I tracked this down to what I think is a RegExp bug in v4l2ctl.ts

In the ReadControls() function, we take the control name and append the variable regexPart to create a RegExp that is matched against the output of v4l2-ctl -l command.

The problem shows when two different controls start the same way: in this case video_bitrate_mode and video_bitrate. The regex will match video_bitrate_mode for both controls. So, when you attempt to set video_bitrate, it takes affect and even gets written to file correctly. But anytime the file is read, the value of video_bitrate_mode will be captured for both controls.

To fix, you could change

var regexPart = ".*value=([0-9]*)";

to

var regexPart = "\\s.*value=([0-9]*)";

This will require whitespace after the control name, which will limit the RegExp to only match the correct control.

@RogerHardiman I created a new branch with some refactors: https://github.com/BreeeZe/rpos/tree/dev
Can you have a look if works on your end?
Maybe you need to do a clean checkout and just run "npm install" and after that run "gulp" to run the default gulp task which compiles the typescript.

I will have some time to explain some more tomorrow if need, I'll probably add a segment to the README.MD file about development.

I found this project because I want to have a few Raspberries (preferably Zero W's) with Pi camera's around my house, connected to Surveillance Station on my SynologyDS1511+. I am fairly new to Linux.

But the installation instructions confuse me. I find something here, but also here. Do I have to combine these or use only one of them?

I'm trying to get this to work on a Raspberry Pi Zero W. But when I run the final command (sudo node rpos.js) I get this error. Does anybody have an idea how to resolve this?

Read IP address 192.168.1.130 from wlan0
Manufacturer : Raspberry Pi
Model : Zero W
HardwareId :
SerialNumber : 000000002d926624
FirmwareVersion : 2.0.0
Starting camera settings webserver on http://192.168.1.130:8081/
Binding DeviceService to http://192.168.1.130:8081/onvif/device_service
Binding MediaService to http://192.168.1.130:8081/onvif/media_service
Uncaught Exception... : Error [ERR_SERVER_ALREADY_LISTEN]: Listen method has been called more than once without closing.
at Server.listen (net.js:1446:11)
at MediaService.SoapService.start (/home/pi/rpos/lib/SoapService.js:26:24)
at Object. (/home/pi/rpos/rpos.js:32:15)
at Module._compile (module.js:641:30)
at Object.Module._extensions..js (module.js:652:10)
at Module.load (module.js:560:32)
at tryModuleLoad (module.js:503:12)
at Function.Module._load (module.js:495:3)
at Function.Module.runMain (module.js:682:10)
at startup (bootstrap_node.js:191:16)

Hi! New to both raspian and github here. Having some issues with getting my camera into Milestone. Have everything installed (?) according to readme, but can't get it to work. Shows up and is discovered with hardware and everything in Milestone, can also connect but shows "no video". Had a couple of blips with video when I look at recording, but unfortuneately cannot identify what exacly I did differently then. If anyone can help, highly appreciated.

This is what i get when node rpos.js (launching driver with modprobe first)

pi@raspberrypi:~/rpos $ Read IP address 10.0.212.200 from eth0
Manufacturer : RPOS Raspberry Pi
Model : Model_PiZeroW_Revision_1.1
HardwareId :
SerialNumber : 0000000005115329
FirmwareVersion : 2.0.4
Starting camera settings webserver on http://10.0.212.200:8081/
Binding DeviceService to http://10.0.212.200:8081/onvif/device_service
Binding MediaService to http://10.0.212.200:8081/onvif/media_service
Binding PTZService to http://10.0.212.200:8081/onvif/ptz_service
Binding ImagingService to http://10.0.212.200:8081/onvif/imaging_service
discovery_service started
ptz_service started
imaging_service started
device_service started
Starting Live555 rtsp server
media_service started
--LAST LINE, nothing more happens--

My rposConfig.json:

"NetworkAdapters" : ["awdl0","eth0", "wlan0", "en0"],
"IpAddress" : "10.0.212.200",
"ServicePort" : 8081,
"Username" : "pi",
"Password" : "xxxx",
"RTSPAddress" : "", "//":"Normally left blank. Used to set RTSP Server Address",
"RTSPPort" : 8554,
"RTSPName" : "h264",
"MulticastEnabled" : false,
"RTSPMulticastName" : "h264m",
"MulticastAddress" : "224.0.0.1",
"MulticastPort" : "10001",
"RTSPServer" : 2, "RtspServerComment" : "## Select RTSP Server > 1:RPOS RTSP Server 2:V4L2 RTSP Server by mpromonet (auto selected if MulticastEnabled=true)",
"PTZDriver" : "none", "PTZDriverComment": "## valid values are none,tenx,pelcod,visca and pan-tilt-hat",
"PTZOutput" : "none", "PTZOutputComment": "## values are none (eg Tenx), serial and tcp",
"PTZSerialPort" : "/dev/ttyUSB0",
"PTZSerialPortSettings" : { "baudRate":2400, "dataBits":8, "parity":"none", "stopBits":1 },
"PTZOutputURL": "127.0.0.1:9999",
"PTZCameraAddress": 1,
"DeviceInformation" : {
"Manufacturer" : "Raspberry Pi",
"Model" : "2 B",
"HardwareId" : ""
},
"logLevel" : 3, "logLevelComment": "## LogLevels are > 1:Error 2:Warning 3:Info 4:Debug",
"logSoapCalls" : false
}

pi@raspberrypi:/rpos $ npm -v
6.7.0
pi@raspberrypi:/rpos $ node -v
v10.15.0

Camera:
PiNoir, working fine with raspistill

EDIT: it is working with server alternative 1, but not mpromonet (2/3)

How easily might it be to use rpos to pull an RTSP stream from another device instead of using video0?

There are a few cameras out there (a couple geovision, but mostly the ubiquiti UVC line) that doesn't support ONVIF despite being a decent h264 1080p camera.

I'd love to put a Pi in acting as a proxy and offering up those RTSP streams via an ONVIF interface.

Hi,
I followed the instructions shown in text file. I used the following to start raspivid

root@raspberrypi:/home/pi/live/raspi# raspivid -o - -fps 25 -t 0 -b 800000 -n -w 1280 -h 720 | ./testRaspi

"h264" stream, from the file "stdin"
Play this stream using the URL "rtsp://192.168.1.123:8554/h264"

(We use port 80 for optional RTSP-over-HTTP tunneling.)

After this, I ran rpos.js. I have been losing my head over this for two days now. When i ran raspivid, it does not create /dev/video0 device as well.

root@raspberrypi:/home/pi/rpos-0.1.0# sudo node rpos.js
execSync('sudo cat /proc/cpuinfo')
Read IP address from awdl0 failed
Read IP address 192.168.1.123 from eth0
Manufacturer : Raspberry Pi
Model : 2 B
HardwareId : 
SerialNumber : 00000000f212401e
FirmwareVersion : 0.1.0
execSync('sudo modprobe bcm2835-v4l2')
Starting camera settings webserver on http://192.168.1.123:8081/
execSync('sudo v4l2-ctl --set-fmt-video=pixelformat=4')
Failed to open /dev/video0: No such file or directory
child_process.js:484
    throw err;
    ^

Error: Command failed: sudo v4l2-ctl --set-fmt-video=pixelformat=4
Failed to open /dev/video0: No such file or directory

    at checkExecSyncError (child_process.js:441:13)
    at Object.execSync (child_process.js:481:13)
    at Function.utils.execSync (/home/pi/rpos-0.1.0/lib/utils.js:94:66)
    at execV4l2 (/home/pi/rpos-0.1.0/lib/v4l2ctl.js:173:22)
    at Object.SetPixelFormat (/home/pi/rpos-0.1.0/lib/v4l2ctl.js:277:9)
    at Camera.setupCamera (/home/pi/rpos-0.1.0/lib/camera.js:129:27)
    at new Camera (/home/pi/rpos-0.1.0/lib/camera.js:44:14)
    at Object.<anonymous> (/home/pi/rpos-0.1.0/rpos.js:23:14)
    at Module._compile (module.js:435:26)
    at Object.Module._extensions..js (module.js:442:10)

Hi,

I am trying to change the part of discovery_service.ts to respond not as NetworkVideoTransmitter but as Device. In if statement of parseString function I changed NetworkVideoTransmitter to Device, as well as in SOAP message I replaced <d:Types>dn:NetworkVideoTransmitter</d:Types> to be <d:Types>tds:Device</d:Types>.

I am testing that with Onvif Test Tool 17 and seems this tool is sending first Device and then NetworkVideoTransmitter probe. While I can see that the message with my changes is replied - I am unable to discover the device with the tool. With NetworkVideoTransmitter it is working.

Can anyone give some hint how to fix that ?

Regards,
Krzysztof

duplicate issue. deleted

When I send the zoom in/out onvif commands to the RPI, the zoom command is transmitted to the RS232 port.
I get on the rs232 following code (Pelco D):
FF 01 00 20 00 00 21
FF 01 00 40 00 00 41
When I send the focus near/far onvif commands to the RPI, the focus commands are not transmitted to the RS232 port.
But I get the STOP command when I send focus near/far. See code (Pelco D):
FF 01 00 00 00 00 01 - it is not right !
I should to get:
FF 01 00 80 00 00 81
FF 01 01 00 00 00 02

On a pi zero W with Raspbian GNU/Linux 9 stretch, nodejs version 4.8.2, I receive the following errors when following the installation instructions (note that previous steps completed OK):

pi@raspberrypi:~/onvif/rpos $ sudo npm install
npm WARN deprecated [email protected]: Typings is deprecated in favor of NPM @types -- see README for more information
npm WARN deprecated [email protected]: Use uuid module instead
npm ERR! 404 Not Found
npm ERR! 404
npm ERR! 404 'gulp-sourcemaps/map-sources' is not in the npm registry.
npm ERR! 404 You should bug the author to publish it
npm ERR! 404 It was specified as a dependency of 'gulp-sourcemaps'
npm ERR! 404
npm ERR! 404 Note that you can also install from a
npm ERR! 404 tarball, folder, or http url, or git url.

npm ERR! System Linux 4.9.41+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install"
npm ERR! cwd /home/pi/onvif/rpos
npm ERR! node -v v4.8.2
npm ERR! npm -v 1.4.21
npm ERR! code E404
npm ERR! fetch failed https://registry.npmjs.org/update-notifier/-/update-notifier-0.6.3.tgz
npm WARN deprecated [email protected]: Please update to minimatch 3.0.2 or higher to avoid a RegExp DoS issue
npm WARN deprecated [email protected]: Please update to minimatch 3.0.2 or higher to avoid a RegExp DoS issue
npm WARN deprecated [email protected]: graceful-fs v3.0.0 and before will fail on node releases >= v7.0. Please update to graceful-fs@^4.0.0 as soon as possible. Use 'npm ls graceful-fs' to find it in the tree.
-
> [email protected] install /home/pi/onvif/rpos/node_modules/serialport
> node-pre-gyp install --fallback-to-build

node-pre-gyp ERR! Tried to download(404): https://github.com/EmergingTechnologyAdvisors/node-serialport/releases/download/4.0.7/serialport-v4.0.7-node-v46-linux-arm.tar.gz
node-pre-gyp ERR! Pre-built binaries not found for [email protected] and [email protected] (node-v46 ABI) (falling back to source compile with node-gyp)
make: Entering directory '/home/pi/onvif/rpos/node_modules/serialport/build'
  CXX(target) Release/obj.target/serialport/src/serialport.o
  CXX(target) Release/obj.target/serialport/src/serialport_unix.o
  CXX(target) Release/obj.target/serialport/src/serialport_poller.o
  SOLINK_MODULE(target) Release/obj.target/serialport.node
  COPY Release/serialport.node
make: Leaving directory '/home/pi/onvif/rpos/node_modules/serialport/build'
npm ERR!
npm ERR! Additional logging details can be found in:
npm ERR!     /home/pi/onvif/rpos/npm-debug.log
npm ERR! not ok code 0


pi@raspberrypi:~/onvif/rpos $ ./node_modules/gulp/bin/gulp.js
module.js:327
    throw err;
    ^

Error: Cannot find module 'gulp-sourcemaps'
    at Function.Module._resolveFilename (module.js:325:15)
    at Function.Module._load (module.js:276:25)
    at Module.require (module.js:353:17)
    at require (internal/module.js:12:17)
    at Object.<anonymous> (/home/pi/onvif/rpos/gulpfile.js:8:18)
    at Module._compile (module.js:409:26)
    at Object.Module._extensions..js (module.js:416:10)
    at Module.load (module.js:343:32)
    at Function.Module._load (module.js:300:12)
    at Module.require (module.js:353:17)

Successful installation to the Raspberry Pi but only about 2 seconds of video can be seen through ONVIF, there will be "NO SIGNAL", I don't know where there is a problem, this is Google Translate, I hope you can understand my meaning

I have a project where I would like to present the video as mjpeg over http. I know the info is in the Onvif standard how to do this. But its alot of info to go thru.
Perhaps someone here could point out some directions or fill in some additional info?

RogerHardiman if you are out there I could use some help. I've gone through the rpos install twice and am having a few minor problems. I feel as though all of the components are installed correctly but am unable to view the stream. I'm stuck. My end goal is to set up a RTSP camera on raspberry and link it into my Geovision Recording server as a RTSP feed across my network. I am unable to browse the feed in ONVIF Device Manager.

Hi tried some of the unimplemented methods and verified them with the XML validity checker in SoapUI.

I think the fault responses are incorrect and should be like this (plus extra error codes for the future)
Even so, this is not 100% correct. It needs a lang='en' attribute on the Text field

var SENDER_NOT_AUTHORIZED = {
  Fault: {
    Code: {
      Value: "soap:Sender",
      Subcode: {
        Value: "soap:NotAuthorized",
      }
    },
    Reason: {
      Text: "Sender not authorized"
    }
  }
};


var UNKNOWN_ACTION = {
  Fault: {
    Code: {
      Value: "soap:Sender",
      Subcode: {
        Value: "soap:UnknownAction",
      }
    },
    Reason: {
      Text: "Unknown Action"
    }
  }
};

var NOT_IMPLEMENTED = {
  Fault: {
    Code: {
      Value: "soap:Sender",
      Subcode: {
        Value: "soap:ActionNotSupported"
      }
    },
    Reason: {
      Text: "Optional Action Not Implemented"
    }
  }
};

Hi there
I'm new to NodeJS but have lots of ONVIF experience.

I tried rpos with ONVIF Device Manager on Windows
ONVIF Device Manager reports a SOAP error with a mis-match between SOAP2003 and SOAP2001 envelopes.

The workaround is to edit rpos/node_modules/soap/lib/server.js and to make this one line change

//  "<soap:Envelope xmlns:soap=\"http://schemas.xmlsoap.org/soap/envelope/\" " +
    "<soap:Envelope xmlns:soap=\"http://www.w3.org/2003/05/soap-envelope\" " +

This lets ONVIF Device Manager receive SOAP messages.
There are still problems with the ONVIF messages but this fixes the first problem.

Roger

I have successfully install the RPOS and able to run it on raspberry Pi.
For rasberry Pi, the python library Picamera support output the video to file and stream at same time, i.e.

camera.start_recording('1.h264', splitter_port=1) 
camera.start_recording(stream, format='h264', splitter_port=2

I am wondering how the above codes can be combined with the RPOS, i.e. RPOS open a stdin stream and the above script output h264 to the stream. Thx.

Hi,
I used C400-I from MYTECH. I had a couple of ONVIF supported camera different model/manuf manage to connect to C400 keyboard but RPOS failed to connect. I check SOAP request from the keyboard controller,

"<s:Envelope xmlns:s="http://www.w3.org/2003/05/soap-envelope"><s:Header><wsse:Security xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd" xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd" xmlns:tplt="http://www.onvif.org/ver10/plus/schema" xmlns:tpl="http://www.onvif.org/ver10/plus/wsdl">wsse:UsernameTokenwsse:Usernameusername1</wsse:Username><wsse:Password Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordDigest">fctLh7e3HR6fKUc4qB6/ihbjoh8=</wsse:Password>wsse:Nonce5FWQrVNVT1MjvLR5mVfXPQ==</wsse:Nonce>wsu:Created2010-01-01T00:19:17Z</wsu:Created></wsse:UsernameToken></wsse:Security></s:Header><s:Body xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"></s:Body></s:Envelope>"

the request used s:Envelopve and s:Body instead of soap:Envelope / soap:Body.
can this be the problem why RPOS failed to connect?

I have another DVR manage to connect to RPOS and control everything. The request is below

"DeviceService - Calltype : received, Data :
<soap:Envelope xmlns:soap="http://www.w3.org/2003/05/soap-envelope" xmlns:tds="http://www.onvif.org/ver10/device/wsdl" xmlns:tt="http://www.onvif.org/ver10/schema">
soap:Header
<wsse:Security soap:mustUnderstand="true" xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd">
<wsse:UsernameToken wsu:Id="UsernameToken-35" xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">
wsse:Usernameadmin</wsse:Username>
<wsse:Password Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordDigest">xi2ZdakrUDkgOpA4ROWIE/5EIDI=</wsse:Password>
<wsse:Nonce EncodingType="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-soap-message-security-1.0#Base64Binary">Jy3sZ5N9TOudLga1rlu/RA==</wsse:Nonce>
wsu:Created2018-08-26T16:04:28Z</wsu:Created>
</wsse:UsernameToken>
</wsse:Security>
</soap:Header>
soap:Body
tds:SetSystemDateAndTime
tds:DateTimeTypeManual</tds:DateTimeType>
tds:DaylightSavingsfalse</tds:DaylightSavings>
tds:TimeZone
tt:TZCST-8</tt:TZ>
</tds:TimeZone>
tds:UTCDateTime
tt:Time
tt:Hour16</tt:Hour>
tt:Minute5</tt:Minute>
tt:Second2</tt:Second>
</tt:Time>
tt:Date
tt:Year2018</tt:Year>
tt:Month8</tt:Month>
tt:Day26</tt:Day>
</tt:Date>
</tds:UTCDateTime>
</tds:SetSystemDateAndTime>
</soap:Body>
</soap:Envelope>
"

Pls advice thanks.

It maybe not an issue.
Could rpos support search via onvif device manager?
Thanks
Bao

Now, I'm trying to use rpos in my RPI board and PI cam. During my testing, I used rpos control webpage and ONVIF device manager to control camera. The streaming is OK in VLC and ONVIF device manager.
I can control camera setting using default control webpage but I cannot find resolution or framerate in there. So I tried them in the ONVIF device manager but I failed. They are not controlled via ONVIF device manager. The resolution list is shown in the dropdown list but my selection is not applied.
How can I solve this?

Could rpos have multiple instances running on alternate ports? (and is a pi3 capable of 2,3,4,x streams?)

this goes with my other post, if a pi can act as a proxy for other RTSP sources that don't support ONVIF, and it can handle at least a few, then rpos would be a pretty slick package!

thanks.

Read IP address 192.168.1.196 from eth0 Manufacturer : Raspberry Pi Model : 2 B HardwareId : SerialNumber : 0000000099774564 FirmwareVersion : 2.0.0 Starting camera settings webserver on http://192.168.1.196:8081/ Binding DeviceService to http://192.168.1.196:8081/onvif/device_service Binding MediaService to http://192.168.1.196:8081/onvif/media_service Uncaught Exception... : Error [ERR_SERVER_ALREADY_LISTEN]: Listen method has bee n called more than once without closing. at Server.listen (net.js:1425:11) at MediaService.SoapService.start (/home/pi/rpos/lib/SoapService.js:26:24) at Object.<anonymous> (/home/pi/rpos/rpos.js:32:15) at Module._compile (internal/modules/cjs/loader.js:654:30) at Object.Module._extensions..js (internal/modules/cjs/loader.js:665:10) at Module.load (internal/modules/cjs/loader.js:566:32) at tryModuleLoad (internal/modules/cjs/loader.js:506:12) at Function.Module._load (internal/modules/cjs/loader.js:498:3) at Function.Module.runMain (internal/modules/cjs/loader.js:695:10) at startup (internal/bootstrap/node.js:201:19)

how to solved the problem?

Hello,
I RPOS 0.1.0 and I run rpos.js all goes well
I tried the latest release of RPOS and impossible to launch (with ts-node?), I to a file not found error typing main.d.ts
How to launch the latest release of RPOS on Raspberry with PICAM?
Thank you.

Hi,
I am using GST-RTSP-SERVER (server option 3) on the Raspberry Pi, the network adapter is set to eth0.
on the Mac I use SecuritySpy and the address is set to same address as eth0(192.168.1.99) and the connection is built successfully.
I tried
`sudo tcpdump -i any port 8554
and got the traffics.

However, when I change the network adapter from eth0 to tun1 (openVPN) on Pi, and on the Mac I set the address to the same address as tun1(10.8.0.156), the connection failed.
I tried
`sudo tcpdump -i any port 8554
but got nothing.

Then, I try to connect the rtsp server by tun1 address, i.e. rtsp://10.8.0.156:8554/h264 and it works. (through VLC player)

I am wondering which part goes wrong?

rposConfig.json:

{
"NetworkAdapters" : ["tun1"],
"IpAddress" : "",
"ServicePort" : 8081,
"Username" : "pi",
"Password" : "pi",
"RTSPAddress" : "", "//":"Normally left blank. Used to set RTSP Server Address",
"RTSPPort" : 8554,
"RTSPName" : "h264",
"MulticastEnabled" : false,
"RTSPMulticastName" : "h264m",
"MulticastAddress" : "224.0.0.1",
"MulticastPort" : "10001",
"RTSPServer" : 3, "RtspServerComment" : "## Select RTSP Server > 1:RPOS RTSP Server 2:V4L2 RTSP Server by mpromonet (auto selected if MulticastEnabled=true)",
"PTZDriver" : "none", "PTZDriverComment": "## valid values are none,tenx,pelcod,visca and pan-tilt-hat",
"PTZOutput" : "none", "PTZOutputComment": "## values are none (eg Tenx), serial and tcp",
"PTZSerialPort" : "/dev/ttyUSB0",
"PTZSerialPortSettings" : { "baudRate":2400, "dataBits":8, "parity":"none", "stopBits":1 },
"PTZOutputURL": "127.0.0.1:9999",
"PTZCameraAddress": 1,
"DeviceInformation" : {
"Manufacturer" : "Raspberry Pi",
"Model" : "2 B",
"HardwareId" : ""
},
"logLevel" : 4, "logLevelComment": "## LogLevels are > 1:Error 2:Warning 3:Info 4:Debug",
"logSoapCalls" : false
}

Im not able to add the device to Milestone (2018 R3) i get pass the first step to add new hardware and it finds the correct hardware model text. But the next step fails with error message:

--
It was not possible to connect to or receive information from the hardware '192.168.123.110'.
Verify that the following is correct: address, port, user name, password and hardware driver.
Alternatively use auto-detection to find the hardware.

Im using the built in rtsp and the pi camera. I can access the RTSP url from VLC.

Any ideas?

This is the last debug output i get:

DeviceService - Calltype : info, Data : Handling POST on /onvif/device_service
DeviceService - Calltype : received, Data :
<SOAP-ENV:Envelope xmlns:SOAP-ENV="http://www.w3.org/2003/05/soap-envelope"
xmlns:SOAP-ENC="http://www.w3.org/2003/05/soap-encoding"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd"
xmlns:ds="http://www.w3.org/2000/09/xmldsig#"
xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"
xmlns:tt="http://www.onvif.org/ver10/schema"
xmlns:tds="http://www.onvif.org/ver10/device/wsdl"
xmlns:wsa5="http://www.w3.org/2005/08/addressing">
SOAP-ENV:Body
tds:GetNetworkInterfaces</tds:GetNetworkInterfaces>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>

DeviceService - Calltype : info, Data : Attempting to bind to /onvif/device_service
DeviceService - Calltype : info, Data : Trying Device from path
DeviceService received request GetNetworkInterfaces
DeviceService - Calltype : replied, Data :
<soap:Envelope xmlns:soap="http://www.w3.org/2003/05/soap-envelope"
xmlns:i0="http://www.onvif.org/ver10/device/wsdl"
xmlns:tns="http://tempuri.org/"
xmlns:tm="http://microsoft.com/wsdl/mime/textMatching/"
xmlns:tds="http://www.onvif.org/ver10/device/wsdl"
xmlns:tt="http://www.onvif.org/ver10/schema">
soap:Body
<tds:GetNetworkInterfacesResponse xmlns:tds="http://www.onvif.org/ver10/device/wsdl"
xmlns="http://www.onvif.org/ver10/device/wsdl">
<tds:NetworkInterfaces token="lo"
xmlns:tt="http://www.onvif.org/ver10/schema">
tt:Enabledtrue</tt:Enabled>
tt:Info
tt:Namelo</tt:Name>
tt:HwAddress00-00-00-00-00-00</tt:HwAddress>
tt:MTU1500</tt:MTU>
</tt:Info>
tt:IPv4
tt:Enabledtrue</tt:Enabled>
tt:Config
tt:Manual
tt:Address127.0.0.1</tt:Address>
tt:PrefixLength8</tt:PrefixLength>
</tt:Manual>
tt:DHCPfalse</tt:DHCP>
</tt:Config>
</tt:IPv4>
</tds:NetworkInterfaces>
<tds:NetworkInterfaces token="eth0"
xmlns:tt="http://www.onvif.org/ver10/schema">
tt:Enabledtrue</tt:Enabled>
tt:Info
tt:Nameeth0</tt:Name>
tt:HwAddressb8-27-eb-d0-b0-81</tt:HwAddress>
tt:MTU1500</tt:MTU>
</tt:Info>
tt:IPv4
tt:Enabledtrue</tt:Enabled>
tt:Config
tt:Manual
tt:Address192.168.123.110</tt:Address>
tt:PrefixLength24</tt:PrefixLength>
</tt:Manual>
tt:DHCPfalse</tt:DHCP>
</tt:Config>
</tt:IPv4>
</tds:NetworkInterfaces>
</tds:GetNetworkInterfacesResponse>
</soap:Body>
</soap:Envelope>

--

pi@raspberrypi:~/rpos $ sudo npm install
(node:8782) [DEP0022] DeprecationWarning: os.tmpDir() is deprecated. Use os.tmpdir() instead.
npm WARN package.json [email protected] No license field.
npm WARN package.json [email protected] No repository field.
npm WARN package.json [email protected] No license field.
npm WARN package.json [email protected] No repository field.
npm WARN package.json [email protected] No repository field.
npm ERR! Error: Method Not Allowed
npm ERR! at errorResponse (/usr/share/npm/lib/cache/add-named.js:260:10)
npm ERR! at /usr/share/npm/lib/cache/add-named.js:203:12
npm ERR! at saved (/usr/share/npm/node_modules/npm-registry-client/lib/get.js:167:7)
npm ERR! at FSReqWrap.oncomplete (fs.js:135:15)
npm ERR! If you need help, you may report this entire log,
npm ERR! including the npm and node versions, at:
npm ERR! http://github.com/npm/npm/issues

npm ERR! System Linux 4.14.71-v7+
npm ERR! command "/usr/bin/node" "/usr/bin/npm" "install"
npm ERR! cwd /home/pi/rpos
npm ERR! node -v v8.11.1
npm ERR! npm -v 1.4.21
npm ERR! code E405
npm ERR!
npm ERR! Additional logging details can be found in:
npm ERR! /home/pi/rpos/npm-debug.log
npm ERR! not ok code 0

I was following the steps and when I ran ./node_modules/gulp/bin/gulp.js I receive the following output:
[17:12:24] Using gulpfile ~/rpos/gulpfile.js
[17:12:24] Starting 'default'...
[17:12:24] Starting 'typings'...
[17:12:26] Finished 'typings' after 2.09 s
[17:12:26] Starting 'compile'...
services/device_service.ts(10,21): error TS2307: Cannot find module 'ip'.
[17:12:38] TypeScript: 1 semantic error
[17:12:38] TypeScript: emit succeeded (with errors)
[17:12:38] Finished 'compile' after 12 s
[17:12:38] Finished 'default' after 14 s

Any ideas on how to resolve this error?

It works, but ONVIF manager does not discover it on the network?

Hi,

I have an IP camera that uses ONVIF protocol. I am running your ONVIF server and when the IP camera sends GetProfiles the ONVIF server throws this error.

DeviceService - Calltype : error, Data : TypeError: Cannot read property 'output' of undefined
    at Object.p.onopentag (/home/pi/rpos-0.1.0/node_modules/soap/lib/wsdl.js:1255:40)
    at emit (/home/pi/rpos-0.1.0/node_modules/soap/node_modules/sax/lib/sax.js:639:35)
    at emitNode (/home/pi/rpos-0.1.0/node_modules/soap/node_modules/sax/lib/sax.js:644:5)
    at openTag (/home/pi/rpos-0.1.0/node_modules/soap/node_modules/sax/lib/sax.js:839:5)
    at Object.write (/home/pi/rpos-0.1.0/node_modules/soap/node_modules/sax/lib/sax.js:1278:15)
    at WSDL.xmlToObject (/home/pi/rpos-0.1.0/node_modules/soap/lib/wsdl.js:1381:5)
    at Server._process (/home/pi/rpos-0.1.0/node_modules/soap/lib/server.js:151:21)
    at IncomingMessage.<anonymous> (/home/pi/rpos-0.1.0/node_modules/soap/lib/server.js:124:14)
    at emitNone (events.js:67:13)
    at IncomingMessage.emit (events.js:166:7)

I would be great if you can give me some pointers how to solve this.

Regards,
Martin

Hi,

I started your application with sudo node rpos.js and its started well and without error.
When Im trying to access the DeviceService and MediaServer, which are avaible on x.x.x.x:8081/onvif/device_service x.x.x.:8081/onvif/media_service I just become a empty page.

It would be awesome if this ONVIF server can show a virtual camera with its current orientation, changed by PTZ commands. Debugging PTZ-based apps would be made so much easier.

We recently got RPOS up and running on both a Raspberry Pi Zero W and a Pi 3.

When using rtspServer ("RTSPServer" : 1 in rposConfig.json) we would get
errors including: "rtspServer: StreamParser::afterGettingBytes() warning: read 4294967295 bytes: expected no more than 15000"

We then switched over to using v4l2rtspserver ("RTSPServer" : 2 in rposConfig.json) and started getting a nice stable image without any errors.

But there is a new issue on the other end of things at the Security Camera DVR, we cannot see the Raspberry Pi's video feed in any multi view screen (where you can see 4 or more cameras at once). We can only see the video feed in single view (just viewing our Raspberry Pi camera). (Note: Tested on two different models of DVR with the same results.)

Has anyone had this issue before? Is there another setting needed for v4l2rtspserver?

Help would be greatly appreciated, relatively new to ONVIF streaming.

Setup has gone well, executed commands:
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install npm
sudo npm install -g npm@latest
sudo apt-get install git
git clone https://github.com/BreeeZe/rpos.git
cd rpos
npm install
npx gulp or ./node_modules/gulp/bin/gulp.js
sudo apt-get install liblivemedia-dev
sh setup_v4l2rtspserver.sh
sudo raspi-config (enabled camera & ssh from menu)
sudo nano /etc/modules --> add this line for load drive at boot --> modprobe bcm2835-v4l2
node rpos.js

node.js starts like:
`Read IP address 192.168.1.236 from wlan0
Manufacturer : RPOS Raspberry Pi
Model : Model_PiZeroW_Revision_1.1
HardwareId :
SerialNumber : 00000000xxxxxxx
FirmwareVersion : 2.0.4
Starting camera settings webserver on http://192.168.1.236:8081/
Binding DeviceService to http://192.168.1.236:8081/onvif/device_service
Binding MediaService to http://192.168.1.236:8081/onvif/media_service
Binding PTZService to http://192.168.1.236:8081/onvif/ptz_service
Binding ImagingService to http://192.168.1.236:8081/onvif/imaging_service
discovery_service started
device_service started
Starting Live555 rtsp server
media_service started
ptz_service started
imaging_service started
rtspServer: Streaming on URL "rtsp://192.168.1.236:8554/h264"

(RTSP-over-HTTP tunneling is not available.)
`
VLC:
I open stream "rtsp://192.168.1.236:8554/h264", loads okay but stops after about 10 seconds.
The RPi Camera led lights up and goes off coinciding with the above.

Hikvision NVR:
The NVR discovers the camera all on its own and its a one click add.
Initially all seems fine but somehow the stream stops and can't be recovered and just says 'no link'.
The RPi Camera led stays on all the time.
Maybe it is something with the protocol, RSP, TDP, UDP, not sure what should be selected?

Boot:
Also how do I get this to start on boot for headless operation? I tried a number of tutorials but none of them worked out?

Is it possible to pull the stream twice from the camera, don't need to but just noticed I needed to make sure either VLC or the NVR was off as this seemed to cause the streaming to stop also.

Any other advice appreciated.

Thanks

I just realised that this didn't use USB camera. As right now I get

child_process.js:484
    throw err;
    ^

Error: Command failed: sudo v4l2-ctl --set-fmt-video=pixelformat=4

    at checkExecSyncError (child_process.js:441:13)
    at Object.execSync (child_process.js:481:13)
    at Function.utils.execSync (/home/pi/rpos-0.1.0/lib/utils.js:94:66)
    at execV4l2 (/home/pi/rpos-0.1.0/lib/v4l2ctl.js:173:22)
    at Object.SetPixelFormat (/home/pi/rpos-0.1.0/lib/v4l2ctl.js:277:9)
    at Camera.setupCamera (/home/pi/rpos-0.1.0/lib/camera.js:129:27)
    at new Camera (/home/pi/rpos-0.1.0/lib/camera.js:44:14)
    at Object.<anonymous> (/home/pi/rpos-0.1.0/rpos.js:23:14)
    at Module._compile (module.js:435:26)
    at Object.Module._extensions..js (module.js:442:10)

Any possibility that this could be added? It is apparantly not common for people to use USB Cameras as quick security cameras and everyone just uses the camera modules 😦

I'm testing rpos with node-onvif module https://github.com/agsh/onvif
Some functions works but some failed.

I found these might be 3 bugs:

1. GetScopes failed
2. HTTP 200 OK
3. Response should be wsdl, but it's returning error message string.

the following functions are OK:
/onvif/device_service:
GetCapabilities
/onvif/media_service
GetProfiles
GetVideoSources

But this Failed:
/onvif/device_service
GetScopes

The content POST to rpos:
POST-to-RPOS.txt

The content Responed from rpos:
Response-from-RPOS.txt

MOLi-rocks/MOLi-DoorMonitor#3 #

This callback won't be called if the request doesn't include any header

Hi- Could you please let me know how two-way audio is supported? Tnx

Read IP address 10.168.1.40 from eth0
Manufacturer : Banana Pi
Model : M2+
HardwareId :
SerialNumber : 02c000812232c635
FirmwareVersion : 0.2.1
Binding DeviceService to http://10.168.1.40:8880/onvif/device_service
Binding MediaService to http://10.168.1.40:8880/onvif/media_service
net.js:1372
throw new ERR_SERVER_ALREADY_LISTEN();
^

Error [ERR_SERVER_ALREADY_LISTEN]: Listen method has been called more than once without closing.
at Server.listen (net.js:1372:11)
at MediaService.SoapService.start (/root/rpos-gateway-0.2.1/lib/SoapService.js:26:24)
at Object. (/root/rpos-gateway-0.2.1/rpos-gateway.js:42:15)
at Module._compile (internal/modules/cjs/loader.js:688:30)
at Object.Module._extensions..js (internal/modules/cjs/loader.js:699:10)
at Module.load (internal/modules/cjs/loader.js:598:32)
at tryModuleLoad (internal/modules/cjs/loader.js:537:12)
at Function.Module._load (internal/modules/cjs/loader.js:529:3)
at Function.Module.runMain (internal/modules/cjs/loader.js:741:12)
at startup (internal/bootstrap/node.js:285:19)

Hi

I'm having issues getting this installed. Running the latest release of Raspian and when I run the npm install from the rpos directory I get the following items logged. I'm running everything under su.

Any ideas?

I installed rpos on a Raspberry Pi and although it is discovered by the Dahua NVR, the video is not generated. After approximately 30 seconds, the NVR stops trying to access the Raspberry Pi camera module. The current setup is the following;

Raspbian 9.6 - Stretch
Raspberry Pi 3 Model B Rev 1.2
Raspberry Pi Camera Module V2 - 8 Megapixel, 1080p

*** Changes made to rposConfig.json ***

"IpAddress" : "192.168.1.147", (this is the Raspberry Pi IP address)
"Username" : "admin",
"Password" : "admin",
"RTSPAddress" : "", "//":"Normally left blank. Used to set RTSP Server Address",
"RTSPPort" : 554, (get the same results even when set to default 8554)
"RTSPServer" : 2,
"Model" : "3 B",
"HardwareId" : "BCM2835"

pi@raspberrypi:~/rpos $ node rpos.js
Read IP address 192.168.1.147 from wlan0
Manufacturer : RPOS Raspberry Pi
Model : Model_B_PI_3
HardwareId : BCM2835
SerialNumber : 00000000d05f7f42
FirmwareVersion : 2.0.4
Starting camera settings webserver on http://192.168.1.147:8081/
Binding DeviceService to http://192.168.1.147:8081/onvif/device_service
Binding MediaService to http://192.168.1.147:8081/onvif/media_service
Binding PTZService to http://192.168.1.147:8081/onvif/ptz_service
Binding ImagingService to http://192.168.1.147:8081/onvif/imaging_service
discovery_service started
imaging_service started
ptz_service started
device_service started
Starting Live555 rtsp server
media_service started
rtspServer error: Error: spawn v4l2rtspserver ENOENT
(node:1232) [DEP0005] DeprecationWarning: Buffer() is deprecated due to security and usability issues. Please use the Buffer.alloc(), Buffer.allocUnsafe(), or Buffer.from() methods instead.

Additionally, the following error generated on a few occasions although the username and password was correct;

Invalid username/password with GetVideoEncoderConfiguration

Should the username and password in the rposConfig.json file be the same as the Raspberry Pi username and password? Also, the camera settings (http://192.168.1.147:8081/) have been set back to the default settings since none of the changes helped with this issue.

If anyone can tell me how to fix this issue, I would appreciate it.

I'm struggling to get this to work. I've worked through the read.me instructions and installed everything correctly (I think). I get some error messages when I run the sudo node rpos.js command.
I'm using an RPi3 with a RPi Camera module v1.3.

Hi, Im trying to start rpos with node using "node rpos.js", but I get an error message after few seconds

/home/pi/rpos-0.1.0/lib/utils.js:94 return utils.notPi() ? "" : require('child_process').execSync(cmd) ^ TypeError: Object #<Object> has no method 'execSync' at Function.utils.execSync (/home/pi/rpos-0.1.0/lib/utils.js:94:66) at Camera.loadDriver (/home/pi/rpos-0.1.0/lib/camera.js:126:15) at new Camera (/home/pi/rpos-0.1.0/lib/camera.js:41:14) at Object.<anonymous> (/home/pi/rpos-0.1.0/rpos.js:23:14) at Module._compile (module.js:456:26) at Object.Module._extensions..js (module.js:474:10) at Module.load (module.js:356:32) at Function.Module._load (module.js:312:12) at Function.Module.runMain (module.js:497:10) at startup (node.js:119:16)

The code seems to default to /dev/video0. When I plugged in an additional usb camera it became /dev/video0 and the RPi cam became /dev/video1. The program then gave me the error message that pixelformat was was an invalid argument.
So this is not a bug, but so that if anyone else has a similar problem with more than one camera, you need a way to change the /dev/video#.
It would be nice to be able to hang more than one camera off the RPi and serve them via this webpage.

Hi - I've worked through the install using a Raspbi Zero W with the NoIR camera module. My objective is to move away from flaky VLC streaming to something more elegant - I'm going to pick up the stream with SecuritySpy.

I'm not very experienced with this sort of thing, so excuse me if this is a dumb question. How can I fix this error in the python that refers to the get-rtsp-launch? I'm pretty confident that the install went OK, but this has me stumped.

The readme suggests that it's an option on the "RTSP Server" line but there are only comments for options 1 and 2, so I kind of assumed that it was 3.

pi@raspicam:~/rpos $ node rpos.js
Read IP address 192.168.0.134 from wlan0
Manufacturer : RPOS Raspberry Pi
Model : Model_PiZeroW_Revision_1.1
HardwareId : 
SerialNumber : 00000000fbfaae5f
FirmwareVersion : 2.0.4
Starting camera settings webserver on http://192.168.0.134:8081/
Binding DeviceService to http://192.168.0.134:8081/onvif/device_service
Binding MediaService to http://192.168.0.134:8081/onvif/media_service
Binding PTZService to http://192.168.0.134:8081/onvif/ptz_service
Binding ImagingService to http://192.168.0.134:8081/onvif/imaging_service
discovery_service started
device_service started
Starting Live555 rtsp server
media_service started
ptz_service started
imaging_service started
rtspServer: Traceback (most recent call last):

rtspServer:   File "./python/gst-rtsp-launch.py", line 44, in <module>
    import gi
ImportError: No module named gi

rtspServer exited with code: 1

EDIT: Just running through the install of this now: https://www.npmjs.com/package/gi
EDIT 2: Didn't make any difference to the error. But this is the snippet:

# --------------------------------------------------------------------------- # 
# Use gi to import GStreamer functionality
# --------------------------------------------------------------------------- # 
import gi
gi.require_version('Gst','1.0')
gi.require_version('GstRtspServer','1.0')
gi.require_version('GstVideo','1.0')
from gi.repository import GObject, Gst, Gio, GstVideo, GstRtspServer, GLib

from threading import Thread, Lock
cam_mutex = Lock()
# -------------------

i get the following message. Is it possible to publish the source code of rtspServer, I assume its a modified live555proxy. That runs fine without this message.

rtspServer: Streaming on URL "rtsp://a.a.a.a:8554/h264"

(RTSP-over-HTTP tunneling is not available.)

Also any luck with implementing login ID and password