vasanthamukilan / experiment-08-encoders-and-decoders-

Experiment-08- Encoders-and-decoders

AIM:

To implement 8 to 3 Encoder and 3to8 Decoder using verilog and validate its outputs

HARDWARE REQUIRED:

– PC, Cyclone II , USB flasher

SOFTWARE REQUIRED:

Quartus prime

THEORY

Encoders

Binary code of N digits can be used to store 2N distinct elements of coded information. This is what encoders and decoders are used for. Encoders convert 2N lines of input into a code of N bits and Decoders decode the N bits into 2N lines.

1. Encoders – An encoder is a combinational circuit that converts binary information in the form of a 2N input lines into N output lines, which represent N bit code for the input. For simple encoders, it is assumed that only one input line is active at a time.

As an example, let’s consider Octal to Binary encoder. As shown in the following figure, an octal-to-binary encoder takes 8 input lines and generates 3 output lines.

Figure -01 3 to 8 Encoder

Implementation –

X = D4 + D5 + D6 + D7 Y = D2 +D3 + D6 + D7 Z = D1 + D3 + D5 + D7 Hence, the encoder can be realised with OR gates as follows:

Figure -02 3 to 8 Encoder implenentation

Decoders

A decoder does the opposite job of an encoder. It is a combinational circuit that converts n lines of input into 2n lines of output.

Let’s take an example of 3-to-8 line decoder. Implementation – D0 is high when X = 0, Y = 0 and Z = 0. Hence,

D0 = X’ Y’ Z’ Similarly,

D1 = X’ Y’ Z D2 = X’ Y Z’ D3 = X’ Y Z D4 = X Y’ Z’ D5 = X Y’ Z D6 = X Y Z’ D7 = X Y Z

Figure -03 8 to 3 Decoder

Figure -04 8 to 3 Decoder implementation

Procedure

• create module encoder and decoder.
• Get inputs and outputs for encoders and decoders.
• perform or operation for encoder and and logic for decoders.
• perform RTL LOGIC and get waveform.

PROGRAM

/*
Program for Endocers and Decoders  and verify its truth table in quartus using Verilog programming.
Developed by:Vasanthamukilan.M
RegisterNumber:212222230167
*/

• ENCODERS

module enc(d0,d1,d2,d3,d4,d5,d6,d7,a,b,c);
input d0,d1,d2,d3,d4,d5,d6,d7;
output a,b,c;
or(a,d4,d5,d6,d7);
or(b,d2,d3,d6,d7);
or(c,d1,d3,d5,d7);
endmodule

• DECODERS

module enc(a,b,c,d0,d1,d2,d3,d4,d5,d6,d7);
input a,b,c;
output d0,d1,d2,d3,d4,d5,d6,d7;
assign d0 = (~a&~b&~c);
assign d1 = (~a&~b&c);
assign d2 = (~a&b&~c);
assign d3 = (~a&b&c);
assign d4 = (a&~b&~c);
assign d5 = (a&~b&c);
assign d6 = (a&b&~c);
assign d7 = (a&b&c);
endmodule 

RTL LOGIC

• ENCODER

• DECODER

TIMING DIGRAMS

• ENCODER

• DECODER

TRUTH TABLE

• ENCODER

• DECODER

RESULTS

Thus the program to desing encoder and decoder is done.