umiddelb / aarch64 Goto Github PK
View Code? Open in Web Editor NEWInteresting stuff about 64 bit ARM devices (pine64, ODROID-C2)
License: MIT License
aarch64's People
Contributors
Stargazers
Watchers
Forkers
ganeshrajulinaro geowebdevcom cybertan janwelker wesley-yang flyingtiger1977 global-localhost global19 global19-atlassian-netaarch64's Issues
Centos on Odroid C2 using Ubuntu image
Maybe you can help me - my Centos on C2 is not booting.
What I did
Step 1: Download the CentOS 7 AArch64 userland tar archive
Downloaded CentOS-7-aarch64-rootfs-7.3.1611.tar.xz
Step 2: Prepare the target media with a formware-only disk image
Downloaded ubuntu64-16.04.2lts-mate-odroid-c2-20170301.img, flashed it to my eMMC 32GB Module
unxz ubuntu64-16.04.2lts-mate-odroid-c2-20170301.img.xz
sudo dd if=ubuntu64-16.04.2lts-mate-odroid-c2-20170301.img of=/dev/sdb bs=4M status=progress && syncwiped out the root file system contents, but leaving untouched:
+ /boot
+ /lib/modules
+ /lib/firmwaresudo mount /dev/sdb2 /media/USB/
cd /media/USB/
sudo rm -f aafirstboot
sudo rm -f .first_boot
sudo rm -Rf bin
sudo rm -Rf dev
sudo rm -Rf etc
sudo rm -Rf home
sudo rm -Rf lib/a*
sudo rm -Rf lib/b*
sudo rm -Rf lib/c*
sudo rm -Rf lib/i*
sudo rm -Rf lib/h*
sudo rm -Rf lib/k*
sudo rm -Rf lib/l*
sudo rm -Rf lib/r*
sudo rm -Rf lib/s*
sudo rm -Rf lib/t*
sudo rm -Rf lib/u*
sudo rm -Rf lib/x*
sudo rm -Rf lib/modprobe.d
sudo rm -Rf lost+found
sudo rm -Rf media
sudo rm -Rf mnt
sudo rm -Rf opt
sudo rm -Rf proc
sudo rm -Rf root
sudo rm -Rf run
sudo rm -Rf sbin
sudo rm -Rf snap
sudo rm -Rf srv
sudo rm -Rf sys
sudo rm -Rf tmp
sudo rm -Rf usr
sudo rm -Rf varStep 3: Copy the rootfs contents to your destination device
sudo tar --numeric-owner -xpJf CentOS-7-aarch64-rootfs-7.3.1611.tar.xz -C /media/USB
sudo blkid
sudo vim /media/USB/etc/fstab
UUID=e139ce78-9841-40fe-8823-96a304a09859 / ext4 defaults 0 0
sudo umount /media/USBStep 4: Reboot to CentOS 7 and have fun
Booting stops with error message
GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
TE: 168459
no sdio debug board detected
BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton
Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
DDR0: 2048MB(auto) @ 912MHz(2T)-13
DataBus test pass!
AddrBus test pass!
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x000000b0
Load bl30 from eMMC, src: 0x00010200, des: 0x01000000, size: 0x00009ef0
Sending bl30........................................OK.
Run bl30...
Load bl301 from eMMC, src: 0x0001c200, des: 0x01000000, size: 0x000018c0
Wait bl30...Done
Sending bl301.......OK.
Run bl301...
l31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00011130
--- UART initialized after reboot ---
[Reset cause: unknown]
[Image: unknown, amlogic_v1.1.3046-00db630-dirty 2016-08-31 09:24:14 tao.zeng@droid04]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipidLoad bl33 from eMMC, src: 0x00034200, des: 0x01000000, size: 0x00073510
: ef be ad de d f0 ad ba ef be ad de not ES chip
[0.283600 Inits done]
secure task start!
high task start!
low task start!
NOTICE: BL3-1: v1.0(debug):4d2e34d
NOTICE: BL3-1: Built : 17:08:35, Oct 29 2015
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-00189-g205c7b3 (Feb 27 2017 - 10:53:13)
DRAM: 2 GiB
Relocation Offset is: 76f32000
-------------------------------------------------
* Welcome to Hardkernel's ODROID-C2
-------------------------------------------------
CPU : AMLogic S905
S/N : HKC213254DFCC431
MAC : 00:1e:06:33:10:b1
BID : HKC2211602
-------------------------------------------------
register usb cfg[1][0] = 0000000077f95058
register usb cfg[0][1] = 0000000077f95078
vpu detect type: 5
vpu clk_level = 7
set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
MMC: aml_priv->desc_buf = 0x0000000073f2ad30
aml_priv->desc_buf = 0x0000000073f2cec0
SDIO Port C: 0, SDIO Port B: 1
[mmc_init] mmc init success
In: serial
Out: serial
Err: serial
----------------------------------
MMC Size : 32 GB
----------------------------------
reading boot-logo.bmp.gz
** Unable to read file boot-logo.bmp.gz **
reading boot-logo.bmp
** Unable to read file boot-logo.bmp **
movi: the partiton 'logo' is reading...
MMC read: dev # 0, block # 61024, count 2048 ... 2048 blocks read: OK
hpd_state=1
[CANVAS]addr=0x3f800000 width=3840, height=1440
set hdmitx VIC = 16
hdmitx phy setting done
set hdmitx VIC = 16
hdmitx phy setting done
Error: Bad gzipped data
There is no valid bmp file at the given address
Net: Meson_Ethernet
Hit [Enter] key twice to stop autoboot: 0
reading boot.ini
6789 bytes read in 2 ms (3.2 MiB/s)
cfgload: applying boot.ini...
cfgload: setenv display_autodetect "true"
cfgload: setenv m "1080p60hz" # Progressive 60Hz
cfgload: setenv m_bpp "32"
cfgload: setenv hpd "true"
cfgload: setenv monitor_onoff "false" # true or false
cfgload: setenv nographics "0"
cfgload: setenv mesontimer "1"
cfgload: setenv disableuhs "false"
cfgload: setenv mmc_removable "true"
cfgload: setenv usbmulticam "false"
cfgload: setenv disable_vu7 "true"
cfgload: setenv condev "console=ttyS0,115200n8 console=tty0" # on both
cfgload: setenv maxcpus "4"
cfgload: setenv max_freq "1536" # 1.536GHz
cfgload: if test "${display_autodetect}" = "true"; then usb pwren; hdmitx edid; fi
USB0: dwc_usb driver version: 2.94 6-June-2012
USB (1) peri reg base: c0000020
USB (1) use clock source: XTAL input, div: 1
USB (1) base addr: 0xc9100000
Force id mode: Host
dwc_otg: Highspeed device found !
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
..............................
edid extension block number : 2
Manufacturer: RTK Model 4c54 Serial Number 1
EDID version: 1.3
Established timings supported:
720x400@70Hz
640x480@60Hz
640x480@72Hz
640x480@75Hz
800x600@56Hz
800x600@60Hz
800x600@72Hz
800x600@75Hz
1024x768@60Hz
1024x768@70Hz
1024x768@75Hz
1280x1024@75Hz
Standard timings supported:
1440x900@60Hz
1440x900@75Hz
1440x900@85Hz
Detailed mode (1) : Clock 74 MHz, 697 mm x 392 mm
1280 1390 1430 1650 hborder 0
720 725 730 750 vborder 0
+hsync +vsync
Detailed mode (1) : Clock 27 MHz, 697 mm x 392 mm
720 736 798 858 hborder 0
480 489 495 525 vborder 0
-hsync -vsync
Monitor ranges (GTF): 50-75Hz V, 24-60kHz H, max dotclock 110MHz
Monitor name: 32V3H-H6A
Has 1 extension blocks
Checksum: 0x29 (valid)
CEA extension block
Extension version: 3
29 bytes of CEA data
VIC 6 1440x480i@60Hz
VIC 7 1440x480i@60Hz
VIC 2 720x480@60Hz
VIC 3 720x480@60Hz
VIC 21 1440x576i@50Hz
VIC 22 1440x576i@50Hz (native)
VIC 17 720x576@50Hz
VIC 18 720x576@50Hz
VIC 19 1280x720@50Hz
VIC 4 1280x720@60Hz
VIC 20 1920x1080i@50Hz
VIC 5 1920x1080i@60Hz
VIC 31 1920x1080@50Hz
VIC 16 1920x1080@60Hz (native)
Linear PCM, max channels 2
Vendor-specific data block, OUI 000c03 (HDMI)
Detailed mode (1) : Clock 27 MHz, 697 mm x 392 mm
720 732 796 864 hborder 0
576 581 586 625 vborder 0
-hsync -vsync
Detailed mode (1) : Clock 74 MHz, 697 mm x 392 mm
1920 2008 2052 2200 hborder 0
540 542 547 562 vborder 0
+hsync +vsync interlaced
Detailed mode (1) : Clock 74 MHz, 697 mm x 392 mm
1920 2448 2492 2640 hborder 0
540 542 547 562 vborder 0
+hsync +vsync interlaced
Detailed mode (1) : Clock 74 MHz, 697 mm x 392 mm
1280 1720 1760 1980 hborder 0
720 725 730 750 vborder 0
+hsync +vsync
Detailed mode (1) : Clock 148 MHz, 697 mm x 392 mm
1920 2448 2492 2640 hborder 0
1080 1084 1089 1125 vborder 0
+hsync +vsync
Checksum: 0xd0 (valid)
bestmode is custombuilt, IEEEOUI 0x000c03
HDMI Mode
cfgload: if test "${m}" = "custombuilt"; then setenv cmode "modeline=${modeline}"; fi
cfgload: if test "${disable_vu7}" = "false"; then setenv hid_quirks "usbhid.quirks=0x0eef:0x0005i
cfgload: setenv bootargs "root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro ${condev} n"
cfgload: setenv loadaddr "0x11000000"
cfgload: setenv dtb_loadaddr "0x1000000"
cfgload: setenv initrd_loadaddr "0x13000000"
cfgload: fatload mmc 0:1 ${initrd_loadaddr} uInitrd
reading uInitrd
9621157 bytes read in 221 ms (41.5 MiB/s)
cfgload: fatload mmc 0:1 ${loadaddr} Image
reading Image
13472384 bytes read in 309 ms (41.6 MiB/s)
cfgload: fatload mmc 0:1 ${dtb_loadaddr} meson64_odroidc2.dtb
reading meson64_odroidc2.dtb
29528 bytes read in 4 ms (7 MiB/s)
cfgload: fdt addr ${dtb_loadaddr}
cfgload: if test "${mesontimer}" = "0"; then fdt rm /meson_timer; fdt rm /cpus/cpu@0/timer; fdt i
cfgload: if test "${mesontimer}" = "1"; then fdt rm /timer; fi
cfgload: if test "${nographics}" = "1"; then fdt rm /reserved-memory; fdt rm /aocec; fi
cfgload: if test "${nographics}" = "1"; then fdt rm /meson-fb; fdt rm /amhdmitx; fdt rm /picdec;i
cfgload: if test "${nographics}" = "1"; then fdt rm /meson-vout; fdt rm /mesonstream; fdt rm /mei
cfgload: if test "${nographics}" = "1"; then fdt rm /deinterlace; fdt rm /codec_mm; fi
cfgload: booti ${loadaddr} ${initrd_loadaddr} ${dtb_loadaddr}
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (uncompressed)
Data Size: 9621093 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Loading Ramdisk to 735fb000, end 73f27e65 ... OK
Loading Device Tree to 000000001fff5000, end 000000001ffff357 ... OK
Starting kernel ...
uboot time: 4619454 us
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14.79-108 (root@a53_b1) (gcc version 5.4.0 20160609 (Ubuntu/Linar7
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] secmon: share mem setup
[ 0.000000] Reserved memory: initialized node linux,secmon, compatible id aml_secmon_memory
[ 0.000000] __reserved_mem_alloc_size: linux,meson-fb
[ 0.000000] fb: Reserved memory: created fb at 0x0000000078000000, size 128 MiB
[ 0.000000] Reserved memory: initialized node linux,meson-fb, compatible id amlogic, fb-memory
[ 0.000000] __reserved_mem_alloc_size: linux,di
[ 0.000000] DI reserved memory: created CMA memory pool at 0x0000000076200000, size 30 MiB
[ 0.000000] Reserved memory: initialized node linux,di, compatible id amlogic, di-mem
[ 0.000000] __reserved_mem_alloc_size: linux,ion-dev
[ 0.000000] linux,ion-dev add multi user:ffffffc001d20568
[ 0.000000] ion_dev mem setup
[ 0.000000] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
[ 0.000000] ppmgr share mem setup
[ 0.000000] linux,ion-dev add multi user:ffffffc001d290f0
[ 0.000000] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
[ 0.000000] __reserved_mem_alloc_size: linux,codec_mm_cma
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000067800000, size 188 MiB
[ 0.000000] Reserved memory: initialized node linux,codec_mm_cma, compatible id shared-dma-pol
[ 0.000000] __reserved_mem_alloc_size: linux,picdec
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000064800000, size 48 MiB
[ 0.000000] Reserved memory: initialized node linux,picdec, compatible id shared-dma-pool
[ 0.000000] __reserved_mem_alloc_size: linux,codec_mm_reserved
[ 0.000000] codec_mm:vdec: reserved mem setup
[ 0.000000] Reserved memory: initialized node linux,codec_mm_reserved, compatible id amlogic,d
[ 0.000000] cma: Reserved 8 MiB at 5fc00000
[ 0.000000] psci: probing function IDs from device-tree
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc074195000 s19584 r8192 d21376 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 478344
[ 0.000000] Kernel command line: root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro c
[ 0.000000] logo: get hdmimode: custombuilt
[ 0.000000] modeline parsing - 1280
[ 0.000000] modeline parsing - 720
[ 0.000000] modeline parsing - 74250
[ 0.000000] modeline parsing - 45000
[ 0.000000] modeline parsing - 60
[ 0.000000] modeline parsing - 1280
[ 0.000000] modeline parsing - 1390
[ 0.000000] modeline parsing - 1430
[ 0.000000] modeline parsing - 1650
[ 0.000000] modeline parsing - 720
[ 0.000000] modeline parsing - 725
[ 0.000000] modeline parsing - 730
[ 0.000000] modeline parsing - 750
[ 0.000000] modeline parsing - 1
[ 0.000000] modeline parsing - 1
[ 0.000000] modeline parsing - 1
[ 0.000000] modeline - horpixels 1280
[ 0.000000] modeline - verpixels 720
[ 0.000000] modeline - pixel_clock 74250
[ 0.000000] modeline - hor_freq 45000
[ 0.000000] modeline - ver_freq 60
[ 0.000000] modeline - hdisp 1280
[ 0.000000] modeline - hsyncstart 1390
[ 0.000000] modeline - hsyncend 1430
[ 0.000000] modeline - htotal 1650
[ 0.000000] modeline - vdisp 720
[ 0.000000] modeline - vsyncstart 725
[ 0.000000] modeline - vsyncend 730
[ 0.000000] modeline - vtotal 750
[ 0.000000] modeline - hsync_polarity 1
[ 0.000000] modeline - vsync_polarity 1
[ 0.000000] modeline - progress_mode 1
[ 0.000000] fmt_para - vic 787
[ 0.000000] fmt_para - name custombuilt
[ 0.000000] fmt_para - pixel_repetition_factor 0
[ 0.000000] fmt_para - progress mode 1
[ 0.000000] fmt_para - scrambler_en 0
[ 0.000000] fmt_para - tmds_clk_div40 0
[ 0.000000] fmt_para - tmds_clk 74250
[ 0.000000] fmt_para - pixel_freq 74250
[ 0.000000] fmt_para - h_freq 45000
[ 0.000000] fmt_para - v_freq 60000
[ 0.000000] fmt_para - hsync_polarity 1
[ 0.000000] fmt_para - vsync_polarity 1
[ 0.000000] fmt_para - h_active 1280
[ 0.000000] fmt_para - h_total 1650
[ 0.000000] fmt_para - h_blank 370
[ 0.000000] fmt_para - h_front 110
[ 0.000000] fmt_para - h_sync 40
[ 0.000000] fmt_para - h_back 220
[ 0.000000] fmt_para - v_active 720
[ 0.000000] fmt_para - v_total 750
[ 0.000000] fmt_para - v_blank 30
[ 0.000000] fmt_para - v_front 5
[ 0.000000] fmt_para - v_sync 5
[ 0.000000] fmt_para - v_back 20
[ 0.000000] dvfs [get_max_freq] - max_freq : 1536000000
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 1498460K/1947648K available (8304K kernel code, 900K rwdata, 3036K rodata)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000] vmemmap : 0xffffff8040010000 - 0xffffff80421d0000 ( 33 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc078000000 ( 1920 MB)
[ 0.000000] .init : 0xffffffc001b95000 - 0xffffffc001c77c80 ( 908 kB)
[ 0.000000] .text : 0xffffffc001080000 - 0xffffffc001b94204 ( 11345 kB)
[ 0.000000] .data : 0xffffffc001c78000 - 0xffffffc001d59280 ( 901 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000006] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483648000ns
[ 0.000025] mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff800000a994
[ 0.000071] local timer MESON TIMER-G mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff8000008
[ 0.000091] local timer MESON TIMER-H mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff800000c
[ 0.000112] local timer MESON TIMER-I mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff8000010
[ 0.000123] Switching to timer-based delay loop
[ 0.000365] Console: colour dummy device 80x25
[ 0.001165] console [tty0] enabled
[ 0.003519] allocated 8388608 bytes of page_cgroup
[ 0.003529] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.003547] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 B)
[ 0.003566] pid_max: default: 32768 minimum: 301
[ 0.003649] Security Framework initialized
[ 0.003678] AppArmor: AppArmor initialized
[ 0.003714] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003726] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.004154] Initializing cgroup subsys debug
[ 0.004169] Initializing cgroup subsys memory
[ 0.004187] Initializing cgroup subsys devices
[ 0.004199] Initializing cgroup subsys freezer
[ 0.004209] Initializing cgroup subsys net_cls
[ 0.004219] Initializing cgroup subsys blkio
[ 0.004228] Initializing cgroup subsys perf_event
[ 0.004240] Initializing cgroup subsys net_prio
[ 0.004250] Initializing cgroup subsys hugetlb
[ 0.004293] ftrace: allocating 29798 entries in 117 pages
[ 0.030072] /cpus/cpu@0: Missing clock-frequency property
[ 0.030102] /cpus/cpu@1: Missing clock-frequency property
[ 0.030114] /cpus/cpu@2: Missing clock-frequency property
[ 0.030126] /cpus/cpu@3: Missing clock-frequency property
[ 0.030140] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.071848] Meson chip version = RevB (1F:B - 0:0)
[ 0.090805] CPU1: Booted secondary processor
[ 0.110784] CPU2: Booted secondary processor
[ 0.130774] CPU3: Booted secondary processor
[ 0.130827] Brought up 4 CPUs
[ 0.130856] SMP: Total of 4 processors activated.
[ 0.131358] devtmpfs: initialized
[ 0.143641] pinctrl core: initialized pinctrl subsystem
[ 0.143910] regulator-dummy: no parameters
[ 0.145685] device-tree: Duplicate name in efusekey, renamed to "key0#1"
[ 0.145715] device-tree: Duplicate name in efusekey, renamed to "key1#1"
[ 0.145744] device-tree: Duplicate name in efusekey, renamed to "key2#1"
[ 0.145771] device-tree: Duplicate name in efusekey, renamed to "key3#1"
[ 0.147681] NET: Registered protocol family 16
[ 0.148533] register canvas platform driver
[ 0.148544] codec:ignore bus ops for cpu=25
[ 0.148552] codec:ignore bus ops for cpu=29
[ 0.148560] codec:register amports ops for bus[0]
[ 0.148568] codec:register amports ops for bus[4]
[ 0.148575] codec:register amports ops for bus[3]
[ 0.148583] codec:register amports ops for bus[2]
[ 0.148590] codec:register amports ops for bus[1]
[ 0.148598] codec:register amports ops for bus[13]
[ 0.148605] codec:register amports ops for bus[2]
[ 0.148613] codec:register amports ops for bus[14]
[ 0.148642] register rdma platform driver
[ 0.149153] vdso: 2 pages (1 code, 1 data) at base ffffffc001c7e000
[ 0.149185] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.149711] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.150989] software IO TLB [mem 0x5c400000-0x5c800000] (4MB) mapped at [ffffffc05c400000-fff]
[ 0.151004] Serial: AMBA PL011 UART driver
[ 0.151091] hdmitx: system: amhdmitx_init
[ 0.151099] hdmitx: system: Ver: 2014May6
[ 0.151130] tv_vout: tv_init_module
[ 0.151141] tv_vout: major number 254 for disp
[ 0.151150] vout_notify: vout_register_server
[ 0.151158] tv_vout: register tv module server ok
[ 0.151186] codec_mm:codec_mm_module_init
[ 0.151317] gxbb clk HIU base is 0xffffff800005a000
[ 0.151327] gxbb clk ao base is 0xffffff800005c000
[ 0.151365] register mpll_clk_out0 success done
[ 0.151376] register mpll_clk_out1 success done
[ 0.151386] register mpll_clk_out2 success done
[ 0.151555] register sys pll success done
[ 0.151598] clkrate [ xtal ] : 24000000Hz
[ 0.151607] clkrate [ 32Khz ] : 32000Hz
[ 0.151615] clkrate [ clk81 ] : 166666666Hz
[ 0.151623] clkrate [ fixed_pll ] : 2000000000Hz
[ 0.151631] clkrate [ fclk_div2 ] : 1000000000Hz
[ 0.151639] clkrate [ fclk_div3 ] : 666666000Hz
[ 0.151648] clkrate [ fclk_div4 ] : 500000000Hz
[ 0.151655] clkrate [ fclk_div5 ] : 400000000Hz
[ 0.151663] clkrate [ fclk_div7 ] : 285714000Hz
[ 0.151691] gxbb clock initialization complete
[ 0.151805] msr_clk_reg0=ffffff800005e75c,msr_clk_reg2=ffffff800006a764
[ 0.152699] amlogic iomap probe done
[ 0.152951] Init pinux probe!
[ 0.153691] pinmux-gxbb c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.153947] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
[ 0.153967] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
[ 0.154030] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
[ 0.154049] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
[ 0.154234] dvfs [scpi_dvfs_get_opps] - new count 6, max_freq 1536000000
[ 0.154672] codec:codec map io source 0x00000000c1100000,size=1048576 to 0xffffff8000680000
[ 0.154692] codec:codec map io source 0x00000000c8820000,size=65536 to 0xffffff80000a0000
[ 0.154710] codec:codec map io source 0x00000000c883c000,size=8192 to 0xffffff8000094000
[ 0.154739] codec:codec map io source 0x00000000c8100000,size=1048576 to 0xffffff8000800000
[ 0.154758] codec:codec map io source 0x00000000d0100000,size=262144 to 0xffffff8000980000
[ 0.154775] codec:codec map io source 0x00000000c8838000,size=1024 to 0xffffff8000092000
[ 0.154836] codec_mm has 2 memory regions
[ 0.154852] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma ok
[ 0.154867] codec_mm:codec_mm_reserved_init 0000000060700000->0000000064800000
[ 0.154879] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.154891] codec_mm:codec_mm_probe mem init done
[ 0.154901] codec_mm:add reserve memory 0000000060700000(aligned 0000000060700000) size=41000)
[ 0.154926] codec_mm has 2 memory regions
[ 0.154937] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma ok
[ 0.154951] codec_mm:codec_mm_reserved_init 0000000060700000->0000000064800000
[ 0.154963] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.154974] codec_mm:codec_mm reserved memory probed done
[ 0.154982] codec_mm:codec_mm_probe ok
[ 0.155554] VPU driver version: v01
[ 0.155564] vpu driver detect cpu type: gxbaby
[ 0.155578] load vpu_clk in dts: 666667000Hz(7)
[ 0.155603] vpu_probe OK
[ 0.155795] hdmitx: system: amhdmitx_probe
[ 0.156009] hdmitx hpd irq = 89
[ 0.156200] hdmitx20: Mapped PHY: 0xc0800000
[ 0.156211] hdmitx20: Mapped PHY: 0xc1104400
[ 0.156232] hdmitx20: Mapped PHY: 0xc8100000
[ 0.156241] hdmitx20: Mapped PHY: 0xc8834000
[ 0.156250] hdmitx20: Mapped PHY: 0xc883a000
[ 0.156260] hdmitx20: Mapped PHY: 0xc883c000
[ 0.156273] hdmitx20: Mapped PHY: 0xd0100000
[ 0.156282] hdmitx20: Mapped PHY: 0xda83a000
[ 0.156296] hdmitx: alread display in uboot 0x10
[ 0.156321] avmute set to 1
[ 0.156657] canvas_probe reg=00000000c8838000,size=400
[ 0.156673] canvas maped reg_base =ffffff800009e000
[ 0.160133] rdma_probe
[ 0.163300] hdmitx: system: irq 80000002
[ 0.191563] bio: create slab <bio-0> at 0
[ 0.192015] SCSI subsystem initialized
[ 0.192165] usbcore: registered new interface driver usbfs
[ 0.192205] usbcore: registered new interface driver hub
[ 0.192258] usbcore: registered new device driver usb
[ 0.192322] media: Linux media interface: v0.10
[ 0.192352] Linux video capture interface: v2.00
[ 0.192401] pps_core: LinuxPPS API ver. 1 registered
[ 0.192410] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@li>
[ 0.192430] PTP clock support registered
[ 0.192591] logo: logo_init
[ 0.192640] Advanced Linux Sound Architecture Driver Initialized.
[ 0.192945] Bluetooth: Core ver 2.18
[ 0.192969] NET: Registered protocol family 31
[ 0.192977] Bluetooth: HCI device and connection manager initialized
[ 0.192991] Bluetooth: HCI socket layer initialized
[ 0.193003] Bluetooth: L2CAP socket layer initialized
[ 0.193026] Bluetooth: SCO socket layer initialized
[ 0.193040] NetLabel: Initializing
[ 0.193047] NetLabel: domain hash size = 128
[ 0.193054] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.193094] NetLabel: unlabeled traffic allowed by default
[ 0.193779] Switched to clocksource Timer-E
[ 0.216337] AppArmor: AppArmor Filesystem Enabled
[ 0.220710] NET: Registered protocol family 2
[ 0.221198] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.221295] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.221515] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.221586] TCP: reno registered
[ 0.221598] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.221640] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.221811] NET: Registered protocol family 1
[ 0.221987] RPC: Registered named UNIX socket transport module.
[ 0.221998] RPC: Registered udp transport module.
[ 0.222006] RPC: Registered tcp transport module.
[ 0.222014] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.222175] Unpacking initramfs...
[ 0.483977] hdmitx: plugin
[ 0.514970] Freeing initrd memory: 9392K (ffffffc0735fb000 - ffffffc073f27000)
[ 0.519314] kvm [1]: Using HYP init bounce page @5a45f000
[ 0.519504] kvm [1]: interrupt-controller@c4304000 IRQ25
[ 0.519725] kvm [1]: kvm_arch_timer: can't find DT node
[ 0.519756] kvm [1]: error initializing Hyp mode: -19
[ 0.520260] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 0.520369] audit: initializing netlink subsys (disabled)
[ 0.520430] audit: type=2000 audit(0.510:1): initialized
[ 0.520970] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.524741] VFS: Disk quotas dquot_6.5.2
[ 0.524881] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.526508] NFS: Registering the id_resolver key type
[ 0.526556] Key type id_resolver registered
[ 0.526564] Key type id_legacy registered
[ 0.526580] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.526611] msgmni has been set to 3433
[ 0.527504] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.527585] io scheduler noop registered (default)
[ 0.527595] io scheduler deadline registered
[ 0.527621] io scheduler cfq registered
[ 0.548932] meson-rng c8834000.rng: hwrng registered
[ 0.549118] [drm] Initialized drm 1.1.0 20060810
[ 0.549163] mali-utgard d00c0000.mali: max pp is 3
[ 0.549175] mali-utgard d00c0000.mali: min pp is 3
[ 0.549186] mali-utgard d00c0000.mali: min clk is 4
[ 0.549205] mali-utgard d00c0000.mali: hiu io source 0xffffff80000d2000
[ 0.549222] mali-utgard d00c0000.mali: hiu io source 0xffffff80000e8000
[ 0.549234] mali-utgard d00c0000.mali: num of pp used most of time 3
[ 0.549245] mali-utgard d00c0000.mali: clock dvfs table size is 6
[ 0.549257] mali-utgard d00c0000.mali: max clk set 4
[ 0.549266] mali-utgard d00c0000.mali: max clk is 4
[ 0.549276] mali-utgard d00c0000.mali: turbo clk set to 5
[ 0.549286] mali-utgard d00c0000.mali: turbo clk is 5
[ 0.549296] mali-utgard d00c0000.mali: default clk is 4
[ 0.549364] mali-utgard d00c0000.mali: ====================0====================
[ 0.549364] clk_freq= 125000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<5
[ 0.549390] mali-utgard d00c0000.mali: ====================1====================
[ 0.549390] clk_freq= 285000000, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<5
[ 0.549416] mali-utgard d00c0000.mali: ====================2====================
[ 0.549416] clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<0
[ 0.549441] mali-utgard d00c0000.mali: ====================3====================
[ 0.549441] clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<0
[ 0.549466] mali-utgard d00c0000.mali: ====================4====================
[ 0.549466] clk_freq= 666000000, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<6
[ 0.549492] mali-utgard d00c0000.mali: ====================5====================
[ 0.549492] clk_freq= 792000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshod=<2
[ 0.551183] gpu cooling register okay with err=0
[ 0.551229] gpu core cooling register okay with err=0
[ 0.551430] Mali: Mali device driver loaded
[ 0.551566] UMP: UMP device driver -jenkins-deb_s905_kernel-108 loaded
[ 0.553992] loop: module loaded
[ 0.554342] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.563522] libphy: stmmac: probed
[ 0.563555] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 0.563566] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 0.564053] usbcore: registered new interface driver cdc_ether
[ 0.564122] usbcore: registered new interface driver cdc_ncm
[ 0.564255] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.564266] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 0.564362] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.564447] usbcore: registered new interface driver cdc_acm
[ 0.564457] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.564501] usbcore: registered new interface driver usb-storage
[ 0.564591] usbcore: registered new interface driver usbserial
[ 0.564625] usbcore: registered new interface driver usbserial_generic
[ 0.564657] usbserial: USB Serial support registered for generic
[ 0.565011] mousedev: PS/2 mouse device common for all mice
[ 0.565315] i2c /dev entries driver
[ 0.565990] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.566045] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.566198] usbcore: registered new interface driver usbhid
[ 0.566207] usbhid: USB HID core driver
[ 0.566379] ==uart0 reg addr = ffffff80002244c0
[ 0.566411] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a mt
[ 0.612879] 00ffffffffffff004a8b544c010000000c110103814627788aa58ea6544a9c26
[ 0.612879] 124546afcf009500950f951901010101010101010101011d007251d01e206e28
[ 0.612879] 5500b9882100001e8c0ad08a20e02d10103e9600b98821000018000000fd0032
[ 0.612879] 4b183c0b000a202020202020000000fc0033325633482d4836410a2020200129
[ 0.612879]
[ 0.612879]
[ 0.612909] 020321714e0607020315961112130414051f90230907078301000065030c0010
[ 0.612909] 008c0ad090204031200c405500b98821000018011d8018711c1620582c2500b9
[ 0.612909] 882100009e011d80d0721c1620102c2580b9882100009e011d00bc52d01e20b8
[ 0.612909] 285540b9882100001e023a80d072382d40102c4580b9882100001e00000000d0
[ 0.612909]
[ 0.612909]
[ 0.612912] EDID Parser:
[ 0.612969] hdmitx: edid: find IEEEOUT
[ 0.612998]
[ 0.613008] hdmitx: video: get current mode: null
[ 0.613011] hdmtix: set audio
[ 0.613020] hdmitx tx_aud_src = 0
[ 0.613045] hdmitx aud_n_para = 24576
[ 0.613061] hdmitx set channel status
[ 2.526660] console [ttyS0] enabled
[ 2.530285] ==uart1 reg addr = ffffff80002264c0
[ 2.534606] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a met
[ 2.543949] enter cpufreq
[ 2.546413] probe cpufreq okay
[ 2.549616] dvfs [scpi_dvfs_get_opps] - new count 6, max_freq 1536000000
[ 2.597051] dwc_otg: usb1: type: 1 speed: 0, config: 0, dma: 0, id: 1, phy: c0000020, ctrl: 0
[ 2.602574] dwc_otg: Core Release: 3.10a
[ 2.603802] dwc_otg: Setting default values for core params
[ 2.609320] dwc_otg: curmode: 1, host_only: 1
[ 2.615825] dwc_otg: Using Buffer DMA mode
[ 2.617679] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.622767] dwc_otg: Working on port type = HOST
[ 2.627421] dwc_otg dwc2_b: DWC OTG Controller
[ 2.631748] dwc_otg dwc2_b: new USB bus registered, assigned bus number 1
[ 2.638487] dwc_otg dwc2_b: irq 63, io mem 0x00000000
[ 2.643468] dwc_otg: -------hcd->flags.d32 = 0
[ 2.647890] dwc_otg: Init: Port Power? op_state=1
[ 2.652522] dwc_otg: Init1: Power Port (0)
[ 2.657011] hub 1-0:1.0: USB hub found
[ 2.660302] hub 1-0:1.0: 1 port detected
[ 2.664354] dwc_otg: usb0: type: 0 speed: 0, config: 0, dma: 0, id: 0, phy: c0000000, ctrl: 0
[ 2.685201] dwc_otg: Core Release: 3.10a
[ 2.685223] dwc_otg: Setting default values for core params
[ 2.689012] dwc_otg: curmode: 1, host_only: 0
[ 2.697504] dwc_otg: Using Buffer DMA mode
[ 2.697527] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.702462] dwc_otg: Working on port type = OTG
[ 2.706955] dwc_otg: Current port type: SLAVE
[ 2.711322] dwc_otg dwc2_a: DWC OTG Controller
[ 2.715675] dwc_otg dwc2_a: new USB bus registered, assigned bus number 2
[ 2.722399] dwc_otg dwc2_a: irq 62, io mem 0x00000000
[ 2.727737] hub 2-0:1.0: USB hub found
[ 2.731110] hub 2-0:1.0: 1 port detected
[ 2.735103] dwc_otg: Dedicated Tx FIFOs mode
[ 2.739359] dwc_otg: using timer detectid change, ffffffc05a53e000
[ 2.745620] BLASTER Driver Init
[ 2.748539] secmon has 1 memory regions
[ 2.752246] secmon: share in base: 0xffffff8000234000, share out base: 0xffffff8000236000
[ 2.760349] secmon secmon: assigned reserved memory node linux,secmon ok
[ 2.767026] secmon: probe done
[ 2.770092] storage: storage in base: 0xffffff8001780000
[ 2.775266] storage: storage out base: 0xffffff8001800000
[ 2.780604] storage: storage block base: 0xffffff8001880000
[ 2.786130] storage: probe done!
[ 2.789894] aml_sd_emmc_probe: line 2954
[ 2.793198] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data r
[ 2.802744] aml_sd_emmc_reg_init 677
[ 2.806032] pdata->caps 60007
[ 2.808896] pdata->caps2 0
[ 2.811569] get property: ocr_avail, value:0x00200080
[ 2.817872] get property: f_min, value:0x00061a80
[ 2.824168] get property: f_max, value:0x0510ff40
[ 2.830458] get property: max_req_size, value:0x00020000
[ 2.836802] get property: irq_in, value:0x00000003
[ 2.843050] get property: irq_out, value:0x00000005
[ 2.849354] get property: power_level, value:0x00000001
[ 2.855656] get property: gpio_cd, str:
[ 2.860907] get property: gpio_power, str:
[ 2.866182] get property: pinname, str:sd
[ 2.866230] dwc_otg: Indeed it is in host mode hprt0 = 00021501
[ 2.877472] get property: jtag_pin, str:
[ 2.882725] get property: card_type, value:0x00000005
[ 2.889028] get property: gpio_dat3, str:
[ 2.894292] get property: gpio_volsw, str:
[ 2.954942] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.954996] aml_sd_emmc_probe: line 2954
[ 2.974883] [aml_is_card_insert] card OUT
[ 2.974931] [aml_is_card_insert] card OUT
[ 2.974931] [ 3.001438] aml_sd_emmc_reg_init 677
[ 3.001552] pdata->caps 80000d47
[ 3.002585] pdata->caps2 80a1
[ 3.005520] get property: ocr_avail, value:0x00200080
[ 3.011806] get property: f_min, value:0x00061a80
[ 3.018110] get property: f_max, value:0x05f5e100
[ 3.024406] get property: max_req_size, value:0x00020000
[ 3.030698] get property: pinname, str:emmc
[ 3.036308] get property: card_type, value:0x00000001
[ 3.042600] get property: gpio_dat3, str:
[ 3.043808] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 3.054279] get property: hw_reset, str:
[ 3.059533] dwc_otg: Indeed it is in host mode hprt0 = 00001101
[ 3.173794] aml_emmc_hw_reset 1356
[ 3.173796] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 3.173966] ion_dev has 1 memory regions
[ 3.186132] fb: osd_init_module
[ 3.186280] fb: viu vsync irq: 35
[ 3.187502] meson-fb has 1 memory regions
[ 3.192819] meson-fb meson-fb: assigned reserved memory node linux,meson-fb ok
[ 3.198653] tv_vout: tv_set_current_vmode[696]fps_target_mode=60
[ 3.204526] tv_vout: mode is 60,sync_duration_den=1,sync_duration_num=60
[ 3.211160] switch_vpu_mem_pd: vencl ON
[ 3.215094] tv_vout: 3Invalid video output modes.
[ 3.219751] tv_vout: new mode =custombuilt set ok
[ 3.224415] vout_serve: vinfo mode is: custombuilt
[ 3.229155] switch_vpu_mem_pd: viu_osd1 ON
[ 3.233206] switch_vpu_mem_pd: viu_osd2 ON
[ 3.237211] switch_vpu_mem_pd: viu_osd_scale ON
[ 3.241824] osd_rdma: osd_rdma_init: rmda_table p=0x5fc49000,op=0x5fc49000 , v=0xffffff8000270
[ 3.250581] emmc: BKOPS_EN bit is not set
[ 3.250585] hdmitx: video: get current mode: custombuilt
[ 3.250596] hdmitx: video: get current mode: custombuilt
[ 3.250622] hdmitx: system: already init VIC = 0 Now VIC = 787
[ 3.250629] hdmitx: rx no SCDC present indicator
[ 3.252638] hdmitx: ddc rd8b error 0x54 0x01
[ 3.254647] hdmitx: ddc rd8b error 0x54 0x01
[ 3.254651] hdmirx version is 1.4 or below
[ 3.254653] hdmitx: system: set pll
[ 3.254655] hdmitx: system: param->VIC:787
[ 3.264720] hdmitx: set clk of VIC = 787 done
[ 3.264744] hdmitx_set_hw[4552] set VIC = 787
[ 3.265706] hub 1-1:1.0: USB hub found
[ 3.265993] hub 1-1:1.0: 4 ports detected
[ 3.313605] [aml_sd_voltage_switch] switch to 1.8V for a non-uhs device.
[ 3.333623] emmc: clk 100000000 SDR mode tuning start
[ 3.333900] rx_tuning_result[0][0] = 10
[ 3.337267] rx_tuning_result[0][1] = 10
[ 3.341064] rx_tuning_result[0][2] = 10
[ 3.344865] rx_tuning_result[0][3] = 10
[ 3.348651] rx_tuning_result[0][4] = 10
[ 3.352449] rx_tuning_result[0][5] = 10
[ 3.356250] rx_tuning_result[0][6] = 10
[ 3.360039] rx_tuning_result[0][7] = 10
[ 3.363834] rx_tuning_result[0][8] = 10
[ 3.367626] rx_tuning_result[0][9] = 10
[ 3.371150] best_win_start =0, best_win_size =10
[ 3.375729] sd_emmc_regs->gclock =0x100024a, sd_emmc_regs->gadjust =0x2000
[ 3.382536] emmc: gclock =0x100024a, gdelay=0x65943045
[ 3.387629] gadjust=0x2000
[ 3.390465] emmc: try set sd/emmc to DDR mode
[ 3.394618] emmc: try set sd/emmc to DDR mode
[ 3.395789] hdmitx: system: phy setting done
[ 3.403150] emmc: clk 100000000 DDR mode tuning start
[ 3.409132] rx_tuning_result[0][0] = 10
[ 3.412917] rx_tuning_result[0][1] = 10
[ 3.416719] rx_tuning_result[0][2] = 10
[ 3.419824] best_win_start =0, best_win_size =3
[ 3.424027] sd_emmc_regs->gclock =0x1000245, sd_emmc_regs->gadjust =0x12000
[ 3.424794] Sink is HDMI device
[ 3.424798] Source reading EDID
[ 3.437137] emmc: gclock =0x1000245, gdelay=0x65943045
[ 3.442219] gadjust=0x12000
[ 3.445103] emmc: new HS400 MMC card at address 0001
[ 3.449896] emmc: clock 100000000, 8-bit-bus-width
[ 3.453790] hdmtix: set audio
[ 3.453797] hdmitx tx_aud_src = 0
[ 3.453808] hdmitx: system: irq 80000001
[ 3.453829] hdmitx aud_n_para = 24576
[ 3.453845] hdmitx set channel status
[ 3.453899] fb: osd_probe vinfo:ffffffc001d22290
[ 3.453903] fb: Frame buffer memory assigned at[ 3.453905] fb: phy: 0x78000000, vir:0xK
[ 3.453914] fb: osd_set_res_bootargs : mode 60
[ 3.453917] fb: fb def : 1280 720 1280 1440 32
[ 3.453918] fb: init fbdev bpp is:32
[ 3.453920] fb: ---------------clear fb0 memory
[ 3.504497] fb: osd[0] canvas.idx =0x40
[ 3.504498] fb: osd[0] canvas.addr=0x78000000
[ 3.504500] fb: osd[0] canvas.width=5120
[ 3.504502] fb: osd[0] canvas.height=1440
[ 3.504756] mmcblk0: emmc:0001 BGND3R 29.1 GiB
[ 3.505272] mmcblk0: p1 p2
[ 3.522849] Console: switching to colour frame buffer device 160x45
[ 3.552177] usb 1-1.3: new full-speed USB device number 3 using dwc_otg
[ 3.563544] fb: Frame buffer memory assigned at
[ 3.566311] fb: phy: 0x7e000000, vir:0xffffff8001a00000, size=1024K
[ 3.580139] fb: osd probe OK
[ 3.580309] vout_serve: vout_init_module
[ 3.581394] vout_serve: meson_vout_probe
[ 3.585228] vout_serve: create vout attribute OK
[ 3.589822] ge2d: ge2d_init_module
[ 3.593139] ge2d: ge2d_dev major:241
[ 3.596827] ge2d: ge2d clock is 400 MHZ
[ 3.600467] ge2d: ge2d: pdev=ffffffc05d6e0a00, irq=182, rstc=0xffffffc05a791d80, clk=ffffffc00
[ 3.609643] ge2d: mapped phy: 0xd0160000
[ 3.613496] ge2d: ge2d start monitor
[ 3.617111] ge2d: ge2d workqueue monitor start
[ 3.617194] codec:Amlogic A/V streaming port init
[ 3.617833] codec:get gate demux control ok ffffffc05a79a580
[ 3.617837] codec:get gate parser_top control ok ffffffc05a79a680
[ 3.617841] codec:get gate vpu_intr control ok ffffffc05a79a780
[ 3.617846] codec:get gate vdec control ok ffffffc05a79a880
[ 3.618017] codec:[tsync_pcr_init]init success.
[ 3.618054] codec:regist mpeg12 codec profile
[ 3.618087] codec:regist mpeg4 codec profile
[ 3.618088] codec:amvdec_vc1 module init
[ 3.618127] codec:regist vc1 codec profile
[ 3.618129] codec:amvdec_h264 module init
[ 3.618177] codec:regist h264 codec profile
[ 3.618178] codec:amvdec_h264mvc module init
[ 3.618209] codec:regist hmvc codec profile
[ 3.618211] codec:amvdec_h264_4k2k module init
[ 3.618247] codec:regist h264_4k2k codec profile
[ 3.618248] codec:amvdec_h265 module init
[ 3.618279] codec:regist hevc codec profile
[ 3.618310] codec:regist mjpeg codec profile
[ 3.618311] codec:amvdec_real module init
[ 3.618345] codec:regist real codec profile
[ 3.618347] codec:amvdec_avs module init
[ 3.618381] codec:regist avs codec profile
[ 3.618422] amvenc_avc_probe -- reserved memory config fail.
[ 3.618423] amvenc_avc - cma memory pool size: 40 MB
[ 3.618436] encode_wq_init.
[ 3.618440] encode start monitor.
[ 3.618608] jpegenc module init
[ 3.618703] codec:picdec_driver_probe called.
[ 3.618706] picdec has 1 memory regions
[ 3.618726] picdec picdec: assigned reserved memory node linux,picdec ok
[ 3.618728] codec:picdec_driver_probe done.
[ 3.618733] codec:reserved memory config fail , use CMA .
[ 3.623805] encode workqueue monitor start.
[ 3.773991] codec:cma memory is 64800000 , size is 3000000
[ 3.774313] input: Mini Keyboard as /devices/platform/dwc2_b/usb1/1-1/1-1.3/1-1.3:1.0/0003:0
[ 3.774517] hid-generic 0003:1997:2433.0001: input,hidraw0: USB HID v1.01 Keyboard [ Mini Ke0
[ 3.777454] input: Mini Keyboard as /devices/platform/dwc2_b/usb1/1-1/1-1.3/1-1.3:1.1/0003:1
[ 3.777667] hid-generic 0003:1997:2433.0002: input,hidraw1: USB HID v1.01 Mouse [ Mini Keybo1
[ 3.821290] codec:0 addr is 64800000################
[ 3.826105] codec:1 addr is 64951800################
[ 3.831107] switch_vpu_mem_pd: vpu_arb ON
[ 3.835194] codec:create_ge2d_work_queue video task ok
[ 3.840296] codec:register clk_set_setting cpu[31]
[ 3.845017] di_module_init ok.
[ 3.847831] di_module_init: major 237
[ 3.851582] di_probe
[ 3.853946] deinterlace has 1 memory regions
[ 3.857851] di reveser memory 0x76200000, size 30MB.
[ 3.862753] deinterlace deinterlace: assigned reserved memory node linux,di ok
[ 3.870022] rdma_register, rdma_table_addr ffffff8000601000 rdma_table_addr_phy 5fc52000 reg_0
[ 3.880093] rdma_register success, handle 1 table_size 8192
[ 3.885611] di_probe allocate rdma channel 1.
[ 3.889919] DI hw version 2.
[ 3.892769] 0x000000c3:Y=c3,U=0,V=0
[ 3.896222] 0x000000c4:Y=c4,U=0,V=0
[ 3.899664] 0x000000c5:Y=c5,U=0,V=0
[ 3.903113] 0x000000c6:Y=c6,U=0,V=0
[ 3.906570] 0x000000c7:Y=c7,U=0,V=0
[ 3.910014] 0x000000c8:Y=c8,U=0,V=0
[ 3.913463] 0x000000c9:Y=c9,U=0,V=0
[ 3.916921] 0x000000ca:Y=ca,U=0,V=0
[ 3.920364] 0x000000cb:Y=cb,U=0,V=0
[ 3.923820] 0x000000cc:Y=cc,U=0,V=0
[ 3.927265] 0x000000cd:Y=cd,U=0,V=0
[ 3.930713] 0x000000ce:Y=ce,U=0,V=0
[ 3.934170] 0x000000cf:Y=cf,U=0,V=0
[ 3.937737] di_probe here.
[ 3.940298] switch_vpu_mem_pd: di_pre OFF
[ 3.944444] efusekeynum: 4
[ 3.946936] efusekeyname: mac offset: 0 size: 6
[ 3.953143] efusekeyname: mac_bt offset: 6 size: 6
[ 3.959373] efusekeyname: mac_wifi offset: 12 size: 6
[ 3.965581] efusekeyname: usid offset: 18 size: 16
[ 3.971871] efuse efuse: probe OK!
[ 3.975296] 6aml_unifykeys_init done!
[ 3.978841] ppmgr module init func called
[ 3.982846] ppmgr_driver_probe called
[ 3.986439] ppmgr has 1 memory regions
[ 3.990148] init ppmgr memsource 74200000->761fffff
[ 3.995099] ppmgr_probe done
[ 3.998014] ionvideo-000: V4L2 device registered as video13
[ 4.003340] [dsp]register dsp to char divece(257)
[ 4.008263] amaudio: driver amaudio succuess!
[ 4.012306] amlvideo_init called
[ 4.015347] amlvideo_create_instance called
[ 4.019638] v4l2_dev.name=:amlvideo-000
[ 4.023494] amlvideo-000: V4L2 device registered as video10
[ 4.028960]
[ 4.028960]
[ 4.028960] VECM init
[ 4.028960]
[ 4.036161] saradc c1108680.saradc: initialized by BL30
[ 4.041046] saradc c1108680.saradc: calibration start:
[ 4.046187] saradc c1108680.saradc: nominal=0, value=0
[ 4.051265] saradc c1108680.saradc: nominal=256, value=249
[ 4.056705] saradc c1108680.saradc: nominal=512, value=507
[ 4.062132] saradc c1108680.saradc: nominal=768, value=767
[ 4.067573] saradc c1108680.saradc: nominal=1023, value=1021
[ 4.073131] saradc c1108680.saradc: calibration end: coef=4048
[ 4.078975] remote: Driver init
[ 4.082192] gpio_key- gpio_key_probe
[ 4.085570] gpio-key c8100000.gpio_keypad: gpio_key: find key_name=0 fail
[ 4.092284] gpio-key: probe of c8100000.gpio_keypad failed with error -22
[ 4.099189] aml-thermal aml-sensor@0: min state:500000 400 1 2
[ 4.105026] aml-thermal aml-sensor@0: not found gpucore node
[ 4.110410] aml-thermal aml-sensor@0: gpu coef:437, pp:3
[ 4.120754] aml-thermal aml-sensor@0: cdev1 set upper to 3
[ 4.122563] aml-thermal aml-sensor@0: cdev2 set upper to 3
[ 4.127820] aml-thermal aml-sensor@0: cdev0 set upper to 3
[ 4.136220] input: cec_input as /devices/virtual/input/input2
[ 4.139138] cectx c810023c.aocec: aml_cec_probe(): can't find hdmirx
[ 4.148434] 6--------------------------------------------------------
[ 4.151686] 6odroid_sysfs_init(321) : Sleep Enable !!
[ 4.154918] random: nonblocking pool is initialized
[ 4.161611] 6--------------------------------------------------------
[ 4.168235] input: vt-input as /devices/virtual/input/input3
[ 4.173751] 6Virtual-Key input driver registered!!
[ 4.178962] adbattery: android dummy battery driver loaded
[ 4.184352] enter aml_soc_platform_pcm2bt_probe
[ 4.188658] divider=16,frac=33920000,SDMval=4523
[ 4.193103] enter aml_pcm_dai_probe
[ 4.196505] [aml-spdif-dai]enter aml_dai_spdif_init
[ 4.201327] aml_spdif_probe
[ 4.204146] enter spdif_dit_probe
[ 4.207893] odroid_hdmi_snd odroid_hdmi: dit-hifi <-> I2S mapping ok
[ 4.214148] GACT probability on
[ 4.216741] Mirror/redirect action on
[ 4.220348] u32 classifier
[ 4.223019] Performance counters on
[ 4.226845] input device check on
[ 4.230456] Actions configured
[ 4.233922] TCP: cubic registered
[ 4.237088] NET: Registered protocol family 17
[ 4.241524] NET: Registered protocol family 15
[ 4.246000] Bluetooth: RFCOMM TTY layer initialized
[ 4.250745] Bluetooth: RFCOMM socket layer initialized
[ 4.255823] Bluetooth: RFCOMM ver 1.11
[ 4.259534] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.264813] Bluetooth: BNEP filters: protocol multicast
[ 4.269961] Bluetooth: BNEP socket layer initialized
[ 4.274870] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.280757] Bluetooth: HIDP socket layer initialized
[ 4.285716] NET: Registered protocol family 35
[ 4.290110] Key type dns_resolver registered
[ 4.294873] Registering SWP/SWPB emulation handler
[ 4.299296] registered taskstats version 1
[ 4.303094] AppArmor: AppArmor sha1 policy hashing enabled
[ 4.308510] regulator-dummy: disabling
[ 4.312444] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 4.318558] [drm] Initialized mali_drm 2.1.1 20140306 on minor 0
[ 4.324376] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 4.330655] [drm] Initialized mali_drm 2.1.1 20140306 on minor 1
[ 4.339229] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 4.343685] 6enter meson_pm_probe!
[ 4.346273] meson_pm_probe done
[ 4.349514] ALSA device list:
[ 4.352223] #0: ODROID-HDMI
[ 4.355645] Freeing unused kernel memory: 904K (ffffffc001b95000 - ffffffc001c77000)
[ 4.756806] vout_serve: vmode set to custombuilt
[ 4.756806]
[ 4.761934] vout_serve: don't set the same mode as current.
[ 4.772070] vout_serve: vmode set to custombuilt
[ 4.772070]
[ 4.777275] vout_serve: don't set the same mode as current.
[ 4.782921] fb: osd0 free scale DISABLE
[ 5.496810] switch_vpu_mem_pd: viu_vd1 OFF
[ 5.499359] switch_vpu_mem_pd: afbc_dec OFF
[ 5.501939] switch_vpu_mem_pd: di_post OFF
[ 5.505992] switch_vpu_mem_pd: viu_vd2 OFF
[ 9.943707] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[ 10.022664] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
[ 10.022664]
[ 10.031853] CPU: 2 PID: 1 Comm: run-init Not tainted 3.14.79-108 #1
[ 10.038059] Call trace:
[ 10.040903] [<ffffffc001088e40>] dump_backtrace+0x0/0x128
[ 10.045824] [<ffffffc001088f8c>] show_stack+0x24/0x30
[ 10.050828] [<ffffffc00188673c>] dump_stack+0x88/0xac
[ 10.055828] [<ffffffc00188531c>] panic+0xdc/0x204
[ 10.060488] [<ffffffc0010b12cc>] do_exit+0xa14/0xa18
[ 10.065402] [<ffffffc0010b1320>] do_group_exit+0x0/0xd8
[ 10.070578] CPU3: stopping
[ 10.073318] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 3.14.79-108 #1
[ 10.079544] Call trace:
[ 10.082212] [<ffffffc001088e40>] dump_backtrace+0x0/0x128
[ 10.087309] [<ffffffc001088f8c>] show_stack+0x24/0x30
[ 10.092312] [<ffffffc00188673c>] dump_stack+0x88/0xac
[ 10.097316] [<ffffffc001090018>] handle_IPI+0x1c0/0x1d0
[ 10.102490] [<ffffffc00108143c>] gic_handle_irq+0x84/0x88
[ 10.107836] Exception stack(0xffffffc05d537e30 to 0xffffffc05d537f50)
[ 10.114219] 7e20: 5d534000 ffffffc0 0189b000 ffffffc0
[ 10.122328] 7e40: 5d537f70 ffffffc0 01085138 ffffffc0 011075a0 ffffffc0 00000000 00000000
[ 10.130435] 7e60: 741b9d14 ffffffc0 00000000 01000000 01de3000 ffffffc0 000007d0 00000000
[ 10.138542] 7e80: d0000000 00001312 00e076de 00000000 3b9aca00 00000000 5d537da0 ffffffc0
[ 10.146650] 7ea0: 000003ff 00000000 0000004c 00000000 00000033 00000000 00000019 00000000
[ 10.154757] 7ec0: 00000001 00000000 00000007 00000000 0000000e 00000000 00000008 00000000
[ 10.162865] 7ee0: e3182ee7 00000000 5d534000 ffffffc0 0189b000 ffffffc0 01d55000 ffffffc0
[ 10.170973] 7f00: 01c85a6c ffffffc0 01d5422c ffffffc0 01aa2b70 ffffffc0 5d534000 ffffffc0
[ 10.179080] 7f20: 0217d000 00000000 01080220 ffffffc0 00000000 00000040 5d537f70 ffffffc0
[ 10.187186] 7f40: 01085134 ffffffc0 5d537f70 ffffffc0
[ 10.192190] [<ffffffc001083dac>] el1_irq+0x6c/0xd8
[ 10.196936] [<ffffffc0011075a0>] cpu_startup_entry+0x238/0x288
[ 10.202712] [<ffffffc00108fa5c>] secondary_start_kernel+0x11c/0x128
[ 10.208920] CPU1: stopping
[ 10.211595] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.79-108 #1
[ 10.217889] Call trace:
[ 10.220334] [<ffffffc001088e40>] dump_backtrace+0x0/0x128
[ 10.225654] [<ffffffc001088f8c>] show_stack+0x24/0x30
[ 10.230657] [<ffffffc00188673c>] dump_stack+0x88/0xac
[ 10.235659] [<ffffffc001090018>] handle_IPI+0x1c0/0x1d0
[ 10.240834] [<ffffffc00108143c>] gic_handle_irq+0x84/0x88
[ 10.246180] Exception stack(0xffffffc05d52be30 to 0xffffffc05d52bf50)
[ 10.252564] be20: 5d528000 ffffffc0 0189b000 ffffffc0
[ 10.260672] be40: 5d52bf70 ffffffc0 01085138 ffffffc0 011075a0 ffffffc0 00000000 00000000
[ 10.268780] be60: 741a1d14 ffffffc0 00000000 01000000 01de3000 ffffffc0 000007d0 00000000
[ 10.276887] be80: d0000000 00001312 00e076de 00000000 3b9aca00 00000000 5d52bda0 ffffffc0
[ 10.284995] bea0: 00000400 00000000 00000000 00000000 00000000 00000000 73a7b700 ffffffc0
[ 10.293102] bec0: 01c979c8 ffffffc0 00000030 00000000 011ee110 ffffffc0 00000000 00000000
[ 10.301210] bee0: 00000000 00000000 5d528000 ffffffc0 0189b000 ffffffc0 01d55000 ffffffc0
[ 10.309318] bf00: 01c85a6c ffffffc0 01d5422c ffffffc0 01aa2b70 ffffffc0 5d528000 ffffffc0
[ 10.317425] bf20: 0217d000 00000000 01080220 ffffffc0 00000000 00000040 5d52bf70 ffffffc0
[ 10.325531] bf40: 01085134 ffffffc0 5d52bf70 ffffffc0
[ 10.330534] [<ffffffc001083dac>] el1_irq+0x6c/0xd8
[ 10.335279] [<ffffffc0011075a0>] cpu_startup_entry+0x238/0x288
[ 10.341056] [<ffffffc00108fa5c>] secondary_start_kernel+0x11c/0x128
[ 10.347265] CPU0: stopping
[ 10.349941] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.79-108 #1
[ 10.356234] Call trace:
[ 10.358795] [<ffffffc001088e40>] dump_backtrace+0x0/0x128
[ 10.363999] [<ffffffc001088f8c>] show_stack+0x24/0x30
[ 10.369002] [<ffffffc00188673c>] dump_stack+0x88/0xac
[ 10.374004] [<ffffffc001090018>] handle_IPI+0x1c0/0x1d0
[ 10.379179] [<ffffffc00108143c>] gic_handle_irq+0x84/0x88
[ 10.384525] Exception stack(0xffffffc001c7bdd0 to 0xffffffc001c7bef0)
[ 10.390909] bdc0: 01c78000 ffffffc0 0189b000 ffffffc0
[ 10.399017] bde0: 01c7bf10 ffffffc0 01085138 ffffffc0 011075a0 ffffffc0 00000000 00000000
[ 10.407125] be00: 74195d14 ffffffc0 00000000 01000000 01de3000 ffffffc0 000007ce 00000000
[ 10.415233] be20: 00000000 00000000 00e04fce 00000000 3b9aca00 00000000 01c7bd40 ffffffc0
[ 10.423340] be40: 000003ff 00000000 00000000 00000000 00000000 00000000 7381ef00 ffffffc0
[ 10.431447] be60: 01c979c8 ffffffc0 00000038 00000000 011ee110 ffffffc0 9c287030 0000007f
[ 10.439555] be80: f6b17c38 0000007f 01c78000 ffffffc0 0189b000 ffffffc0 01d55000 ffffffc0
[ 10.447662] bea0: 01c85a6c ffffffc0 01d5422c ffffffc0 01aa2b70 ffffffc0 01c78000 ffffffc0
[ 10.455770] bec0: 01c85980 ffffffc0 01080478 ffffffc0 00000000 00000040 01c7bf10 ffffffc0
[ 10.463876] bee0: 01085134 ffffffc0 01c7bf10 ffffffc0
[ 10.468879] [<ffffffc001083dac>] el1_irq+0x6c/0xd8
[ 10.473623] [<ffffffc0011075a0>] cpu_startup_entry+0x238/0x288
[ 10.479402] [<ffffffc001883ea4>] rest_init+0x8c/0x98
[ 10.484322] [<ffffffc001b9582c>] start_kernel+0x36c/0x384
ssh Permission denied
I have followed the instructions.
When booting the device Centos 7, I have encountered an error
/bin/bash Permission denied
Please help me overcome this error
error log secure
Jun 12 16:32:46 localhost sshd[1134]: ssh_selinux_change_context: setcon system_u:system_r:sshd_net_t:s0 from system_u:system_r:kernel_t:s0 failed with Permission denied [preauth] Jun 12 16:32:46 localhost sshd[1134]: Accepted password for root from 192.168.1.123 port 61828 ssh2 Jun 12 16:32:46 localhost sshd[1134]: pam_systemd(sshd:session): Failed to create session: Access denied Jun 12 16:32:46 localhost sshd[1134]: pam_unix(sshd:session): session opened for user root by (uid=0) Jun 12 16:32:46 localhost sshd[1134]: sshd_selinux_copy_context: setcon failed with Permission denied Jun 12 16:32:46 localhost sshd[1139]: sshd_selinux_copy_context: setcon failed with Permission denied Jun 12 16:32:46 localhost sshd[1134]: Received disconnect from 192.168.1.123 port 61828:11: disconnected by user Jun 12 16:32:46 localhost sshd[1134]: Disconnected from 192.168.1.123 port 61828 Jun 12 16:32:46 localhost sshd[1134]: pam_unix(sshd:session): session closed for user root
suggestion for the centos on odroid c2 wiki
I found your wiki for using centos with the odroid c2, https://github.com/umiddelb/aarch64/wiki/Install-CentOS-7-on-the-ODROID-C2
Very nice writeup. I had one minor suggestion for it that simplifies the losetup step. I'm somewhat partial to using kpartx which handles identifying the partition offsets and makes the device available via loopback. There's an example of using it in the README at http://mirror.centos.org/altarch/7/isos/aarch64/ReadMe.txt
Thanks again for the write-up!
Centos on Odroid C2
Hi Uli,
First of all, thanx for the write up of Install-CentOS-7-on-your-favourite-ARMv8-ARM64-AArch64-board
(https://github.com/umiddelb/aarch64/wiki/Install-CentOS-7-on-your-favourite-ARMv8-ARM64-AArch64-board)
Second: I just want to share my experience with Centos on a ordroid C2.
Third: I’m just an enthusiastic amateur with limited experience of the hole RHEL family.
(So for all readers beware: I’m not sure the following is completely accurate.)
I found the Archlinux-Arm (Alarm) the best base to merge with a Centos rootfs. It comes with a initramfs instead of a initrd. Dracut happily plays with this Alarm initramf. Downside is complicated updating of the kernel, the init ramfs is created during the update of the kernel. Especially with a eMMC module.
My workaround is a “multi” boot setup containing a boot partition (u-boot and the kernel) and multiple partitions with rootfs’s. by editing setenv bootargs in boot.ini you can choose which distro starts (root=/dev/mmcblk0pX). One of them is arch-arm where the kernel can be updated, then you must distribute the kernel modules to all other partitions/distros.
IMO It’s recommendable to disable kernel updates if you use the rootfs provided by Alternative Architecture Centos SIG.
Do you know if someone is working on a spec-file to build a kernel?
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.