No RSSI on FC about flyplusi6x

[qba667]

@Creautre, It looks you did it right, can you please show me photos of Display screens from I6X? Press down to get second screen where channels 11 and 12 are displayed. If values will be displayed correctly we can continue searching.

[Creautre]

Thanks for the quick response. I took several pictures of menu points that might be of interest.

Btw. the Quad was active when I took the pictures so the Receiver was Powered

http://pasteall.org/pic/2489d2c021df41bb356523456478097c
http://pasteall.org/pic/c88da037892cf470a7571e2c1f5ef89a

[Creautre]

Edit: when i Look closely it appears that Channels 11 and 12 in the remote Display are flickering for milliseconds to another value than 1000 even when they Quad is not powered. This flickering is not visible on the Receiver Tab in cleanflight

[dolphin78]

On Mon, Apr 23, 2018 at 11:41 AM Apicalis ***@***.***> wrote: Edit: when i Look closely it appears that Channels 11 and 12 in the remote Display are flickering for milliseconds to another value than 1000 even when they Quad is not powered. This flickering is not visible on the Receiver Tab in cleanflight — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#1 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AFjbV26PSD9hGNQCtRNj-akUxVU1H0Xmks5trfYcgaJpZM4Te-0O> .

What receiver do you use?

[Creautre]

Says it on the first post bottom sentence. It's the x6b and I am using ibus

[qba667]

@Creautre Can you check in System -> RX Setup -> Sensors list what sensors are available?

[Creautre]

@qba667 There is only 1 Sensor listed and it says "Tx V1:5.44V" which I guess is my Remote Battery Voltage if I am not mistaken

EDIT: I went to "Choose sensors" and have the choice to add 3 Sensors. All of them only have the options "None" or "Tx V1"

[dolphin78]

Looks like you’re not getting any telemetry, not just the RSSI. You should be getting RX voltage and RSSI sensors even with stock firmware. Was it working before you flashed the RSSI firmware? Do you have afhds 2a enabled in your TX?

[Creautre]

I never really bothered to look into telemetry since I read all the stuff I thought I needed from the OSD.
I checked the RX Standard and it is AFHDS 2A

[qba667]

@Creautre as @dolphin78 wrote you have no telemetry link. Please verify your receiver - is the link established at all? You should see at least RX voltage - when bound - almost all receivers support this feature. It is possible to measure other direction RSSI but it is not what we need because it must be signal level that RX see. Please try to figure out what is wrong wrong with the telemetry link.

[Creautre]

@qba667 @dolphin78 How can i establish the telemetry link?

I thought this was always active anyways. I think I had a telemetry link with the old firmware in my first quad that I crashed. Because there i used the Ext Bat Sensor on the receiver. On my new Quad where I am using the exact same x6b receiver I never wired the Bat connection.

Is there any way to force the Telemetry link?

[louisFpv]

Hi, thx for your great work.
I have updated my FX-i6x by using the updater Integrated.1.0.42.1560. It is success to find 12ch in the Display. However, I cannot active the 11 or 12ch the Menu> System> Aux switches. The max ch in Aux switches menu I can active is 10.
Please help me how to active the 11, 12... aux switches,
Regards

[qba667]

@louisFpv I have already answered another issue. Please check channel values in Disply menu.

[louisFpv]

@qba667 Thx

[Creautre]

@qba667 Sorry for opening this issue. It's officially been solved, my receiver somehow didn't send telemetry. I now connected a Flit10 Receiver and everything is working perfectly fine!

Thank you for your work