pyrestone / jetson-fan-ctl Goto Github PK

The development package is not required by this pure-python script. You should adjust the recommendation to offer just python3 as a dependency.

Getting this error when trying to install.

Hi!
Great work with the fan, it works for me fine but I always get these errors on startup:

ubuntu python3[4733]: Maximizing clock speeds with jetson_clocks
ubuntu python3[4733]: /usr/bin/jetson_clocks: line 316: : No such file or directory
ubuntu python3[4733]: /usr/bin/jetson_clocks: line 317: : No such file or directory
ubuntu python3[4733]: Error: Failed to max GPU frequency!
ubuntu python3[4733]: Setup complete.
ubuntu python3[4733]: Running normally.

Would you have any advice on how to resolve them?

Cheers!

The automagic-fan service is active and running on boot but the fan doesn't start spinning unless the service gets restarted.

I was able to fix it by adding this line to the service file.

ExecStartPre=/bin/sleep 5

I installed this package on my AGX Xavier. It works! I love it.
But after a while, the system starts to automatically reboot sporadically.
I wonder why and investigate a little bit:
Setup: AGX Xavier is running at MAXN power mode, historically I would manually run "sudo jetson_clocks" to turn on the fan to 255 (maximal speed). But just once to change the fan speed.
Potential root cause of sporatical reset:
Now after install automagic-fan, every 2 secs, the fanctl.py will write fanspeed to /sys/devices/pwm-fan/target_pwm.
Hypothesis: while AGX is running at MAXN and it is known issue that in this mode AGX is very voltage/current sensitive. Every time when set_speed(spd) occurs, it might potentially create the voltage swing that might upset AGX to trigger the reset.
Avoiding unnecessary set_speed(spd) strategy:
I modify the code to do following to reduce the frequency of set_speed(spd) while meets my need of thermal management yet still enjoy the silent when the unit is idle:

1. check if current spd is the same as prev_speed, then there is no need to call set_speed()
2. introduce optional (configurable) WATERMARK feature that only set the fan speed at two level (HI_FAN, LO_FAN) using watermark algorithms (HI_TEMP, LO_TEMP). This further reduce the frequency of touching set_speed()
3. make default UPDATE_INTERVAL longer from 2 sec to 17 sec.

I tested it with my AGX Xavier running MAXN power mode and the result is very stable now.

If you like to review my code and please provide me permission to push (branch: watermark) changes to you. Please let me know ; ))

Thank you again for your code. It helps a lot.

Hi. First of all, thanks for publishing this software. However, I can't force it to run. When I'm trying to manually restart the service it says, that the service is masked. When I'm trying to unmask it, nothing happens.

Any ideas how to fix that?

jetson@nano:~$ sudo service automagic-fan restart
Failed to restart automagic-fan.service: Unit automagic-fan.service is masked.
jetson@nano:~$ sudo systemctl unmask automagic-fan.service
jetson@nano:~$ sudo service automagic-fan restart
Failed to restart automagic-fan.service: Unit automagic-fan.service is masked.
jetson@nano:~$ sudo systemctl status automagic-fan.service 
● automagic-fan.service
     Loaded: masked (Reason: Unit automagic-fan.service is masked.)
     Active: inactive (dead)

I have jetson_stats on my machine and it has a service that controls when jetson_clocks is run... Will jetson-fan-ctl upset that given the config files has a MAX_PERF value which causes jetson_clocks to be run?

I've recompiled the kernel because I wanted to enable kvm. The commands that I have issued are :

git clone https://github.com/OE4T/linux-tegra-4.9.git
cd linux-tegra-4.9
git checkout oe4t-patches-l4t-r32.7.3
cp /proc/config.gz .
gunzip config.gz
mv config .config
make menuconfig —> (enable kvm)
make -j4
make -j4 modules_install
make -j4 Image
mv /boot/Image-kvm Image2-kvm
cp arch/arm64/boot/Image /boot/Image

the dtb file to use is called : tegra210-p3448-0000-p3449-0000-a02.dtb 
and the extlinux.conf is something like this :

TIMEOUT 30
DEFAULT primary

MENU TITLE L4T boot options

LABEL primary
MENU LABEL primary kernel
LINUX /boot/Image
INITRD /boot/initrd
FDT /boot/tegra210-p3448-0000-p3449-0000-a02.dtb
APPEND ${cbootargs} quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0

Unfortunately Xfce freezes a second before to be fully loaded and I suspect that the cause is your script. Is it supposed to work on the scenario that I have explained ? Yes,I've removed your script,giving these commands :

systemctl disable automagic-fan
mv /usr/local/bin/automagic-fan /usr/local/bin/automagic-fan_
mv /lib/systemd/system/automagic-fan.service /lib/systemd/system/automagic-fan.service_
mv /etc/automagic-fan /etc/automagic-fan_

but the problem still there. xfce won't fully load. But i still suspect that the cause is your script. I would like to know your opinion.

I get the following when running the script.

=>sudo service automagic-fan status
● automagic-fan.service - Automagic fan control
Loaded: loaded (/lib/systemd/system/automagic-fan.service; enabled; vendor preset: enabled)
Active: active (running) since Sun 2020-05-10 19:35:19 CEST; 13h ago
Main PID: 2579 (python3)
Tasks: 1 (limit: 4163)
CGroup: /system.slice/automagic-fan.service
└─2579 /usr/bin/python3 -u /usr/local/bin/automagic-fan/fanctl.py

May 10 19:35:19 nano systemd[1]: Started Automagic fan control.
May 10 19:35:24 nano python3[2579]: Maximizing clock speeds with jetson_clocks
May 10 19:35:24 nano python3[2579]: /usr/bin/jetson_clocks: line 269: : No such file or directory
May 10 19:35:24 nano python3[2579]: /usr/bin/jetson_clocks: line 270: : No such file or directory
May 10 19:35:24 nano python3[2579]: Error: Failed to max GPU frequency!
May 10 19:35:24 nano python3[2579]: Setup complete.
May 10 19:35:24 nano python3[2579]: Running normally.

Lines 269/270

  	echo 0 > "${GPU_RAIL_GATE}"
  	cat "${GPU_MAX_FREQ}" > "${GPU_MIN_FREQ}"