pfreguia / nuki.homey Goto Github PK

✖ Homey App did not validate against level debug:
Found multiple Flow card triggers with the id "nuki_state_changed", all Flow cards should have a unique id.
can you help with that ?

why take actions via web / app / or other devices/user up to 4 minutes to state update ?? the cloud connection reacts faster than local connection ? i think an individual polling time in the settings failed app v3.0.3 (opener + bridge) , the log is also not correct to that what happens . or not logged .

after setup all new i got the message "Could not get device by id"

I have a Nuki Opener and a Nuki Smartlock 1.0 and 3.0. I installed version 3.10.0 of Nuki direct via CLI. When searching for new openers I can pair my Nuki Opener. However, both smartlocks cannot be found, despite beeing paired with my bridge. When searching for a lock it shows that no new devices were found.

The bridge has firmware version 2.14.0, the Opener 1.8.1, Smartlock 1 1.14.1, the Smartlock 3 3.3.5.

Any ideas what I am doing wrong or is this a bug?

As stated here the app does not work when using a software/smartphone bridge. Therefore I would appreciate being able to manually enter the IP adress of the bridge during the pairing process.

Are you planning to support the Nuki Opener?

Hello,
I have bought both Nuki 3.0 Pro smart lock and Homey Pro just recently, with a huge hopes to integrate that all along with my other IoT (Xiaomi, Tuya, Netatmo, ..) into a single environment.
However with Nuki I can't get that working in any way, not with the official app from Athom neither with yours. Is there a chance to have this smart lock supported by your application as well please? Thank you very much in advance.

Action item will open the door and 3x done and works without an issue.

But after locking the door and then open the door I get a timeout issue.

Also locking and unlocking give a timeout issue and give status device is not available.

move it to the second ui page off a
device , an at the first which also acts when presses device in overview without funktion, if you use homekit it
is better status messaging , when you remove it you must create a VD as lock must create flows ..... . thx , and for very .... user you can create a VD as lock or switch ... who acts as security protection for the nuki unlatch , an flow if nuki latch unlock and VD not pressed before ( + max time 3 sec ) do nothing otherwise unlock the door . i have a 3 Virtual device as lock create that runs 👌.

p.s if the unlatch acts not as push button or plug / switch in app , also as lock device handling you must press the device long ui opens , ....
example opener device in the cloud app . there so many options you can secure your homey. so please don t remove options. Smarthome is not a 0815 thing , a little more power on the brain can help them 😅.

thx 😊

When adding a new device (opener or lock) I get the error "Timed out after 30000ms". I now use the hardware bridge with Firmware 2.5.2, an Opener with 1.4.9 and a lock with 1.9.6. Calling https://api.nuki.io/discover/bridges gives me:

"
{"bridges":[{"bridgeId":xxx,"ip":"192.168.178.138","port":8080,"dateUpdated":"2020-07-10T06:40:13Z"}],"errorCode":0}

where I replaced the acutal bridge ID with xxx.

I am using verison 1.3.0 of the app. Before installing it, I did uninstall the old app and deleted all devices. The http API is activated on the bridge.

hi when you make a flow with the condition :
If:
floor motion detection active
And:
The doorbell rang less than 5 seconds ago
then:
do anything .

is not working

the doorbell rang more than x seconds ago
works . but this works anytime it can be ring days before when you can not set the less seconds in a condition.

example
when:

• floor motion detector is active

and:

• RingToOpen is unlocked
• The doorbell rang for more then 5 deconds
• The doorbell rang for less then 300
  seconds ago

then:

• open nuki smartlock after 15 seconds.

I used this flow because i must go 2 floors up and the auto unlock function of my nuki smartlock react to fast ( on the way to the 1 floor it starts open door . when i arrived the 2 floor the door was already opened and now closed .

I missed an option in the nuki app where you can set a time for : smartlock detected user autounlock after x seconds . when the way is to long after bluetooth detected phone .auto unlock of smartlock is unusable for this people .
or maybe the way from street over garden to the door is long enough same thing

with this conditions of your app (when they worked right ) i can solve this problem .
please look at this error .
and thanks for the great work.

by the way another question:
is it possible to set the doorbell signal off with the api ? so if you can set a time for doorbell is inactive (Nightmode) ?

Dear all

I can control my opener with the app (open / status). So I assume the connection is working.
But the flow which has "Someone Rings" is not executed. Do I miss something?

best
Pascal