TCPBurn is a replay tool which focuses on concurrency. All TCP-based applications which could be replayed could be stressed by this powerful tool .
1) Network latency could be reserved
2) No need to bind multiple IP addresses and the number of client IP addresses
is unlimited
3) The maximum number of concurrent users is restricted to bandwidth, memory
and CPU processing power
4) Only TCP-based applications that could be replayed are supported
1) Stress testing
2) Comet
3) Performance testing
As shown in the above Figure, TCPBurn consists of two parts: tcpburn and intercept. While tcpburn runs on the test server and sends the packets from pcap files, intercept runs on the assistant server and does some assistant work, such as passing response info to tcpburn.
tcpburn reads packets from pcap files and does the necessary processing (including TCP interaction simulation, network latency control, and common upper-layer interaction simulation), and uses raw socket output technique by default to send packets to the target server(pink arrows).
The only operation needed in the target server for TCPBurn is setting appropriate route commands to route response packets(green arrows) to the assistant server.
intercept is responsible for passing the response header to tcpburn. By capturing the response packets, intercept will extract response header information and send the response header to tcpburn using a special channel(purple arrows). When tcpburn receives the response header, it utilizes the header information to modify the attributes of pcap packets and continues to send another packet. It should be noticed that the responses from the target server are routed to the assistant server which should act as a black hole.
--with-debug compile tcpburn with debug support (saved in a log file)
--pcap-send send packets at the data link layer instead of the IP layer
--single if intercept is configured with "--single" option, so does tcpburn
--comet replay for comet applications
a) Install intercept on the assistant server
git clone git://github.com/session-replay-tools/intercept.git
cd intercept
./configure --single
make
make install
b) Running intercept on the assistant server(root privilege or the CAP_NET_RAW capability is required):
./intercept -F <filter> -i <device,>
Note that the filter format is the same as the pcap filter.
For example:
./intercept -i eth0 -F 'tcp and src port 80' -d
Intercept will capture response packets of the TCP-based application which
listens on port 80 from device eth0
Set route commands appropriately to route response packets to the assistant server
For example:
Assume 65.135.233.161 is the IP address of the assistant server. We set the following
route commands to route all responses to the 62.135.200.x's clients to the assistant
server.
route add -net 62.135.200.0 netmask 255.255.255.0 gw 65.135.233.161
a) Install tcpburn on the test server
git clone git://github.com/session-replay-tools/tcpburn.git
cd tcpburn
if not comet scenarios
./configure --single
else
./configure --single --comet
endif
make
make install
./tcpburn -x historyServerPort-targetServerIP:targetServerPort -f <pcapfile,>
-s <intercept address> -u <user num> -c <ip range,>
For example:
Assume 65.135.233.160 is the IP address of the target server and 10.110.10.161 is the
internal IP address of the assistant server and 65.135.233.161 is the external IP
address of the assistant server.
./tcpburn -x 80-65.135.233.160:80 -f /path/to/80.pcap -s 10.110.10.161
-u 10000 -c 62.135.200.x
tcpburn extracts packets from 80.pcap file on dst port 80 and replays these to the
target server 65.135.233.160 which runs the application listening on port 80. Total
sessions replayed are 10000 and client IP addresses used are belonging to 62.135.200.x
series. tcpburn connects to the assistant server(10.110.10.161) for asking response
information.
1) All sessions are retrieved from pcap files and make sure the sessions in pcap files
are complete.
2) tcpburn uses raw socket to send packets by default, and if you want to avoid
ip_conntrack problems or get better performance, configure tcpburn with "--pcap-send"
and refer to "./tcpburn -h" for how to set appropriate parameters for running.
3) The test server and the assistant server could share the same machine.
4) For comet applications, exclude publish sessions if they exist in pcap files.
5) tcpburn could not replay TCP-based sessions that could not be replayed,
such as SSL/TLS sessions
6) ip_forward should not be set on the assistant server.
7) Root privilege or the CAP_NET_RAW capability is required
8) Please execute "./tcpburn -h" or "./intercept -h" for more details.
- 2014.09 v1.0 TCPBurn released
Have a bug or a feature request? Please open a new issue. Before opening any issue, please search for existing issues.
Copyright 2019 under the BSD license.