jp112sdl / hb-uni-sen-dummy-beacon

dummy device to send cyclic message or reply with an ack for inactive homematic devices

HB-UNI-Sen-DUMMY-BEACON

Dummy-Device zum Vermeiden von "Kommunikation gestört"-Servicemeldungen von bis zu 8 inaktiven HomeMatic-Geräten (nur HM-RF, kein HmIP / Wired).

Die ist z.B. sehr nützlich bei saisonal verwendeten Geräten, die in Programmen, Diagrammen etc. verwendet, jedoch z.B. in Wintermonaten nicht genutzt werden. Denn ein Ablernen der Geräte während der Nutzungspausen würde bedeuten, dass Programme nach dem erneuten Anlernen wieder bearbeitet werden müssten.

Es erfolgt:

• eine automatische Aussendung zyklischer Telegramme an die CCU (bei Sensoren)
• eine Quittung (Ack) von Steuerbefehlen der CCU (bei Aktoren)

Wird ein Telegramm des "echten" Gerätes empfangen, so wird das Aussenden der Fake-Telegramme automatisch deaktiviert, um Kollisionen / Fehlverhalten zu vermeiden.

Hardware

Bauteile

• 1x Arduino Pro Mini (3.3V 8MHz)
• 1x CC1101 Funkmodul 868MHz
• 1x FTDI Adapter
• 1x Taster
• 1x Widerstand 330Ohm
• 1x LED

Verdrahtung

Die Stromversorgung erfolgt indealerweise aus einem 5V-Steckernetzteil und wird an RAW (+) sowie GND (-) des Pro Mini angeschlossen.

Software

Arduino IDE

• Arduino IDE herunterladen und installieren

• AskSinPP Bibliothek als ZIP herunterladen

• notwendige Bibliotheken in der Arduino IDE hinzufügen:

  • Sketch -> Bibliothek einbinden -> .ZIP-Bibliothek hinzufügen
    • heruntergeladene AskSinPP Bibliothek ZIP-Datei auswählen
  • Sketch -> Bibliothek einbinden -> Bibliotheken verwalten
    • im Suchfeld folgende Bibliotheken suchen und installieren:
      • EnableInterrupt
      • Low-Power

• Board einstellen:

  • Board: Arduino Pro or Pro Mini
  • Prozessor: ATmega328P (3.3V, 8 MHz)
  • Port: COM-Port des FTDI Adapters
    

• Sketch öffnen. (Die 3 Dateien HB-UNI-Sen-DUMMY-BEACON.ino, HB_Device.h und HB_MultiChannelDevice.h müssen sich in einem gemeinsamen Verzeichnis befinden.)

• Sketch hochladen:

  • Sketch
    • Hochladen

HomeMatic

Addon installieren

Damit das Gerät von der CCU erkannt und unterstützt wird, ist es erforderlich, das JP-HB-Devices-addon zu installieren.
Es wird mindestens Version 1.18 benötigt.

Anlernen an HomeMatic

Das Anlernen erfolgt nach Installation des Addons wie man es von anderen HomeMatic-Geräten gewohnt ist:

• Geräte anlernen -> HM-Gerät anlernen klicken
• Config-Taster am Arduino Pro Mini kurz drücken
• das neue Gerät erscheint anschließend im Posteingang

Konfiguration

Damit das Dummy-Device weiß, wessen Telegramme es nun ersetzen soll, müssen die Adressen (Achtung: nicht die Seriennummern!) der Geräte im Dummy-Device hinterlegt werden.
Hintergrund-Info: Anhand der Seriennummer wird ein HomeMatic Gerät nicht im Funkprotokoll identifiziert. Dies geschieht ausschließlich über die Geräteadresse. Die Adresse (RF_ADDRESS) eines HomeMatic-Geräts ist leider nicht ohne Umwege in der WebUI ersichtlich. Sie lässt sich beispielsweise als hexadezimalwert dem Device-File im Dateisystem /etc/config/rfd/<SERIAL.dev> entnehmen:

Um das Hinterlegen der gewünschten Adressen weitestgehend zu automatisieren ist wie folgt vorzugehen:

1. In den Geräteeinstellungen des Dummy-Device ist ein Kanal umzubenennen.
Der Kanalname muss beginnen mit X gefolgt von der Seriennummer, des HomeMatic Geräts, das abgebildet werden soll.
Beispiel:

• das HomeMatic-Gerät hat die Seriennummer: NEQ0386972
• der Kanalname des Dummy-Device muss lauten: XNEQ0386972

2. Ausführen des Parametrierungsskripts auf der CCU.
(Sollte die Seriennummer des Dummy-Device nicht JPBEACON01 lauten, so ist diese im Skript entpsrechend zu ändern (string FAKEDEV = "JPBEACON01";).)
Durch Ausführen des Skripts werden nun die Adressen der Geräte ausgelesen und zum Dummy-Device übertragen.

3. Einstellungen

In den Einstellungen können Parameter

• für das Gerät
  • Max. Sendeversuche: Anzahl der Sendeversuche bei bidirektionalen Nachrichten
• je Kanal (also je emuliertem Gerät)
  • Geräte-ID: RF-Adresse; hier dezimal! (wird vom Skript gesetzt)
  • Übertragungsintervall: alle x Sekunden wird ein zyklisches Telegramm gesendet (nur bei Sensoren, bei Aktoren (außer HM-ES-PMSw1-xxx) auf 0 lassen!); die eingegebene Zeit muss kleiner sein als der von HomeMatic erwartete Wert (siehe unten stehende Tabelle)
  • Telegrammübertragung aktiviert: Dummy-Nachrichten werden für dieses Gerät generiert
  • Status-Wert: z.B. bei Fensterkontakt "geschlossen" (0) oder "offen" (1) übertragen

festgelegt werden.

4. Betrieb
Unter "Status und Bedienung"->"Geräte" ist eine Übersicht der aktivierten Kanäle zu sehen.


Achtung: Der Status der Telegrammübertragung (aktiviert / deaktiviert) muss nicht zwingend der Einstellung wie unter 3. festgelegt entsprechen!
Es wird der tatsächliche Status wiedergegeben. Ist z.B. ein Kanal in 3. aktiviert und es wird jedoch ein Funktelegramm vom "echten" HomeMatic-Gerät empfangen, wird der Kanal in der Übersicht deaktiviert!

Diese README ist garantiert nicht vollständig! Bei Unklarheiten bitte ein Issue erstellen.

CYCLIC_TIMEOUT Werte der HomeMatic-Geräte:

Device Type	Timeout	Model ID
HM-CC-RT-DN	600	0x0095
HM-CC-RT-DN-BoM	552	0x00bd
HM-CC-SCD	88200	0x0056
HM-CC-TC	600	0x0039
HM-CC-VD	3600	0x003a
HM-ES-PMSw1-DR	600	0x00ea
HM-ES-PMSw1-Pl	600	0x00ac
HM-ES-PMSw1-Pl-DN-R1	600	0x00d7
HM-ES-PMSw1-Pl-DN-R2	600	0x00e2
HM-ES-PMSw1-Pl-DN-R3	600	0x00e3
HM-ES-PMSw1-Pl-DN-R4	600	0x00e4
HM-ES-PMSw1-Pl-DN-R5	600	0x00e5
HM-ES-PMSw1-S	600	0x00f6
HM-ES-TX-WM	600	0x00de
HM-SCI-3-FM	88200	0x005f
HM-Sec-MDIR	1200	0x004a
HM-Sec-MDIR-2	1200	0x00c0
HM-Sec-MDIR-3	1200	0x00f7
HM-Sec-RHS	88200	0x0030
HM-Sec-SC	88200	0x002f
HM-Sec-SC-2	88200	0x00b1
HM-Sec-SCo	10000	0x00c7
HM-Sec-SD	1209600	0x0042
HM-Sec-SD-2	259200	0x00aa
HM-Sec-TiS	88200	0x0043
HM-Sec-WDS	88200	0x0045
HM-Sec-WDS-2	88200	0x00b2
HM-Sen-LI-O	88200	0x00fd
HM-Sen-RD-O	88200	0x00a7
HM-Sen-Wa-Od	88200	0x009f
HM-TC-IT-WM-W-EU	600	0x00ad
HM-WDS10-TH-O	600	0x003d
HM-WDS100-C6-O	600	0x0040
HM-WDS100-C6-O-2	600	0x00ae
HM-WDS20-TH-O	600	0x003c
HM-WDS30-OT2-SM	40000	0x00a8
HM-WDS30-OT2-SM-2	40000	0x0102
HM-WDS30-T-O	600	0x000f
HM-WDS40-TH-I	600	0x003f
HM-WDS40-TH-I-2	600	0x00bc

hb-uni-sen-dummy-beacon's Issues

Device mit mehreren channels

Hallo, super Idee! Habe die Hard- und Software problemlos installiert.
Mein Problem:
Ich möchte einen Fenstersensor "ZEL STG RM FFK" (entspricht dem HM-Sec-SC) damit emulieren. Dieser hat einen Sabotagekontakt der natürlich anspricht, wenn ich die Batterie aus dem Sensor entferne.
Wie läßt sich ein gesczlossener Sabotagekontakt emulieren?
Vielen Dank!
Gruß kmbach

Fehlermeldungen beim Kompilieren

Wenn ich die Firmware bei Arduino-Ide kompiliere bekomme ich immer die gleiche Fehlermeldung:

`Arduino: 1.8.11 (Windows 10), Board: "Arduino Pro or Pro Mini, ATmega328P (3.3V, 8 MHz)

C:\Program Files (x86)\arduino-1.8.11\arduino-builder -dump-prefs -logger=machine -hardware C:\Program Files (x86)\arduino-1.8.11\hardware -hardware C:\Users\mathi\AppData\Local\Arduino15\packages -tools C:\Program Files (x86)\arduino-1.8.11\tools-builder -tools C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -tools C:\Users\mathi\AppData\Local\Arduino15\packages -built-in-libraries C:\Program Files (x86)\arduino-1.8.11\libraries -libraries C:\Users\mathi\OneDrive\Documents\Arduino\libraries -fqbn=arduino:avr:pro:cpu=8MHzatmega328 -ide-version=10811 -build-path C:\Users\mathi\AppData\Local\Temp\arduino_build_962732 -warnings=none -build-cache C:\Users\mathi\AppData\Local\Temp\arduino_cache_655553 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avr-gcc-7.3.0-atmel3.6.1-arduino5.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.arduinoOTA-1.3.0.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avrdude-6.3.0-arduino17.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -verbose M:\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON\HB-UNI-Sen-DUMMY-BEACON.ino
C:\Program Files (x86)\arduino-1.8.11\arduino-builder -compile -logger=machine -hardware C:\Program Files (x86)\arduino-1.8.11\hardware -hardware C:\Users\mathi\AppData\Local\Arduino15\packages -tools C:\Program Files (x86)\arduino-1.8.11\tools-builder -tools C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -tools C:\Users\mathi\AppData\Local\Arduino15\packages -built-in-libraries C:\Program Files (x86)\arduino-1.8.11\libraries -libraries C:\Users\mathi\OneDrive\Documents\Arduino\libraries -fqbn=arduino:avr:pro:cpu=8MHzatmega328 -ide-version=10811 -build-path C:\Users\mathi\AppData\Local\Temp\arduino_build_962732 -warnings=none -build-cache C:\Users\mathi\AppData\Local\Temp\arduino_cache_655553 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avr-gcc-7.3.0-atmel3.6.1-arduino5.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.arduinoOTA-1.3.0.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -prefs=runtime.tools.avrdude-6.3.0-arduino17.path=C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr -verbose M:\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON\HB-UNI-Sen-DUMMY-BEACON.ino
Using board 'pro' from platform in folder: C:\Program
Using core 'arduino' from platform in folder: C:\Program
Detecting libraries used...
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o nul
Alternatives for EnableInterrupt.h: [[email protected]]
ResolveLibrary(EnableInterrupt.h)
-> candidates: [[email protected]]
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o nul
Alternatives for AskSinPP.h: [[email protected]]
ResolveLibrary(AskSinPP.h)
-> candidates: [[email protected]]
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o nul
Alternatives for LowPower.h: [[email protected]]
ResolveLibrary(LowPower.h)
-> candidates: [[email protected]]
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\AlarmClock.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\Globals.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\HMID.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\Led.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\PhaseCut.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes128_dec.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes128_enc.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_dec.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_enc.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_invsbox.c" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_keyschedule.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_sbox.c" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\gf256mul.S" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\gf256mul.cpp" -o nul
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master\LowPower.cpp" -o nul
Generating function prototypes...
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\preproc\ctags_target_for_gcc_minus_e.cpp"
"C:\Program Files (x86)\arduino-1.8.11\tools-builder\ctags\5.8-arduino11/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\preproc\ctags_target_for_gcc_minus_e.cpp"
Sketch wird kompiliert...
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp.o"
In file included from M:\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON-master\HB-UNI-Sen-DUMMY-BEACON\HB-UNI-Sen-DUMMY-BEACON.ino:10:0:

C:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt/EnableInterrupt.h:22:121: note: #pragma message: NOTICE: *** EnableInterrupt library version 0.9.7. This is not a problem. Keep calm, and carry on. ***

#pragma message("NOTICE: *** EnableInterrupt library version 0.9.7. This is not a problem. Keep calm, and carry on. ***")

                                                                                                                     ^

Compiling libraries...
Compiling library "EnableInterrupt"
Compiling library "AskSinPP-master"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -x assembler-with-cpp -flto -MMD -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\gf256mul.S" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\gf256mul.S.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_invsbox.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_invsbox.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_sbox.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_sbox.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\PhaseCut.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\PhaseCut.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\HMID.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\HMID.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes128_enc.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes128_enc.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes128_dec.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes128_dec.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\Globals.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\Globals.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_dec.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_dec.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\Led.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\Led.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\AlarmClock.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\AlarmClock.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_enc.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_enc.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\aes_keyschedule.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_keyschedule.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master\gf256mul.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\gf256mul.cpp.o"
Compiling library "Low-Power-master"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master" "-IC:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master" "C:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master\LowPower.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\Low-Power-master\LowPower.cpp.o"
Compiling core...
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -x assembler-with-cpp -flto -MMD -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring_pulse.S" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_pulse.S.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring_analog.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_analog.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring_pulse.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_pulse.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\WInterrupts.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WInterrupts.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring_shift.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_shift.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\wiring_digital.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_digital.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -c -g -Os -w -std=gnu11 -ffunction-sections -fdata-sections -MMD -flto -fno-fat-lto-objects -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\hooks.c" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\hooks.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\CDC.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\CDC.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\HardwareSerial2.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial2.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\HardwareSerial3.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial3.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\IPAddress.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\IPAddress.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\HardwareSerial1.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial1.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\PluggableUSB.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\PluggableUSB.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\HardwareSerial0.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial0.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\HardwareSerial.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\Print.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Print.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\Stream.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Stream.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\USBCore.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\USBCore.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\Tone.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Tone.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\WMath.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WMath.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\WString.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WString.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\abi.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\abi.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\main.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\main.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega328p -DF_CPU=8000000L -DARDUINO=10811 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files (x86)\arduino-1.8.11\hardware\arduino\avr\cores\arduino\new.cpp" -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\new.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_pulse.S.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WInterrupts.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\hooks.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_analog.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_digital.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_pulse.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\wiring_shift.c.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\CDC.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial0.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial1.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial2.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\HardwareSerial3.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\IPAddress.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\PluggableUSB.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Print.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Stream.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\Tone.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\USBCore.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WMath.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\WString.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\abi.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\main.cpp.o"
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc-ar" rcs "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\core.a" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\core\new.cpp.o"
Gebauter Kern wird archiviert (zwischengespeichert) in: C:\Users\mathi\AppData\Local\Temp\arduino_cache_655553\core\core_arduino_avr_pro_cpu_8MHzatmega328_360589d6bc9a4e22c267f1a7a2bcfec2.a
Linking everything together...
"C:\Program Files (x86)\arduino-1.8.11\hardware\tools\avr/bin/avr-gcc" -w -Os -g -flto -fuse-linker-plugin -Wl,--gc-sections -mmcu=atmega328p -o "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732/HB-UNI-Sen-DUMMY-BEACON.ino.elf" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\gf256mul.S.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_invsbox.c.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_sbox.c.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\AlarmClock.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\Globals.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\HMID.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\Led.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\PhaseCut.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes128_dec.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes128_enc.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_dec.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_enc.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\aes_keyschedule.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\gf256mul.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\Low-Power-master\LowPower.cpp.o" "C:\Users\mathi\AppData\Local\Temp\arduino_build_962732/core\core.a" "-LC:\Users\mathi\AppData\Local\Temp\arduino_build_962732" -lm
C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\libraries\AskSinPP-master\Globals.cpp.o (symbol from plugin): In function `__vector_21':

(.text+0x0): multiple definition of `as::resetFunc'

C:\Users\mathi\AppData\Local\Temp\arduino_build_962732\sketch\HB-UNI-Sen-DUMMY-BEACON.ino.cpp.o (symbol from plugin):(.text+0x0): first defined here

collect2.exe: error: ld returned 1 exit status

Bibliothek EnableInterrupt in Version 0.9.7 im Ordner: C:\Users\mathi\OneDrive\Documents\Arduino\libraries\EnableInterrupt wird verwendet
Bibliothek AskSinPP-master in Version 4.1.2 im Ordner: C:\Users\mathi\OneDrive\Documents\Arduino\libraries\AskSinPP-master wird verwendet
Bibliothek Low-Power-master in Version 1.6 im Ordner: C:\Users\mathi\OneDrive\Documents\Arduino\libraries\Low-Power-master wird verwendet
exit status 1
Fehler beim Kompilieren für das Board Arduino Pro or Pro Mini.

fehlen vielleicht noch Bibliotheken, die bei der Doku nicht angegeben wurden?
Anders kann ich mir das jetzt nicht vorstellen.
ich wollte gerade den Bibliothek-Manager als Screenshot beifügen, damit Du siehst, daß auch alle Bibliotheken (AskSinpp, Low-Power und Enableinterrupt) vorhanden sind.
Gruß,
Mathias