joelucid / betaflight Goto Github PK

Hi, I'm new here so forgive me if this has already been stated and this is the wrong thread.

I just flashed my SP Racing Pro F3 v1 board with the BF 4.1.1 PE with RPM filtering firmware.
I didn't see anywhere mention the LED support was removed, however, my LED boards haven't been working since the update.

Is this a bug or has the support been removed?

Also is it possible to remove something else to enable VTX tables again?
It's my only way of controlling my VTX right now

Again thank you Joe for all the work you do.

My main reason for upgrading to 4.1.1 was to add an ExpressLRS receiver to UART 2 and RPM filtering with my Bluejay ESCs.

Hardware Info:

• Copter: Leader 120
• FC: F3 OMNIBUS Board

Software Info:

• runs fine with official 3.4.x as well as self-compiled BF4.1 and BF4.2-RC2

Issue with Performance Edition:

• I flashed betaflight_4.1.1_OMNIBUS_SPEKTRUM.hex and CPU-Usage is 100%.

Expected behavior:

• CPU usage is similiar to other Betaflight variants

Additional Info:
I am running that device with a self-compiled variant using Betaflight 4.2-RC1 and CPU-Usage is less than 20% (jumps between 13-18% when bidirectional DShot is disabled or 40-50% when enabled).
Reason for self-compiled BF4.2: using SRXL2 Spektrum receiver.

I'd like to try out the JoeLucid Performance Edition because my gyro and pid "rate/hz"-values are not as close to the target value as they should be so I hope using the Performance Edition will help there.

CRAZYBEEF3FR 4.1.1 EA3 has problems with current and voltage when voltage is above 4.0V. It shows 0 amps, 0 mah and voltage is shown as more than 4.3.
When voltage drops below 4.0 you have to rearm to get good reading.

Hello,

when using CRAZYBEEF3RX 4.1 target from here on Happymodel Snapper6 with Frsky R-XSR soldered to TX pad with fport, FPORT configured, Serial enabled, RX bound, the receiver tab in BF does not show the all the channels and does not react to radio input.

The same set-up with BF 4.0.4 is working fine. All channels are shown and working.

It would be great if you could take a look at this. I am suspecting that perhaps this is a deliberate decision as there is an assumption that folks would be using the internal SPI_RX receiver, however, with Frsky move to ACCESS 2.1 you cannot bind D8 or D16 any longer when internal module of taranis is upgraded too.

Thanks

M

I am curious if there is coming a new update?
And whether the new bfp f3 also has rpm filter support, for the ff_piko_blx?

Unfortunately the targets BETAFLIGHTF3 and FF_PIKOBLX don't support rpm filtering yet due to resource conflicts.

Is there any Chance RPM Filtering will be available on FF_PIKOBLX?
What resource does it conflict with?
I own an aircraft that utilizes this Flight Controller and would like to enable RPM Filtering.

Thanks.
-Markus

Just wanted to ask, if you could provide an "USB broken - rescue" image? I'm currently using my omnibus F3 board with broken USB port and UART1 is the default MSP.

Hi. I'm using LittleBee ESCs with 16.73 firmware.
Motor beeps last OK (high-tone)beeps before 4.1.1-EA3
And I flashed FC to 4.1.1-EA3. After that not beeps OK sign. Only beeps initial beeps.
Only IMPULSERCF3 has problem with DSHOT among my F3s, I've set RPM Filter well with other F3 FCs..
After that, motors not beeps last sign.