Coder Social home page Coder Social logo

nocache's Introduction

nocache - minimize filesystem caching effects

The nocache tool tries to minimize the effect an application has on the Linux file system cache. This is done by intercepting the open and close system calls and calling posix_fadvise with the POSIX_FADV_DONTNEED parameter. Because the library remembers which pages (ie., 4K-blocks of the file) were already in file system cache when the file was opened, these will not be marked as "don't need", because other applications might need that, although they are not actively used (think: hot standby).

Use case: backup processes that should not interfere with the present state of the cache.

Installation and Usage

Just type make. Then, prepend ./nocache to your command:

./nocache cp -a ~/ /mnt/backup/home-$(hostname)

The command make install will install the shared library, man pages and the nocache, cachestats and cachedel commands under /usr/local. You can specify an alternate prefix by using make install PREFIX=/usr.

Debian packages are available, see https://packages.qa.debian.org/n/nocache.html.

Please note that nocache will only build on a system that has support for the posix_fadvise syscall and exposes it, too. This should be the case on most modern Unices, but kfreebsd notably has no support for this as of now.

Testing

For testing purposes, I included two small tools:

  • cachedel calls posix_fadvise(fd, 0, 0, POSIX_FADV_DONTNEED) on the file argument. Thus, if the file is not accessed by any other application, the pages will be eradicated from the fs cache. Specifying -n will repeat the syscall the given number of times which can be useful in some circumstances (see below).
  • cachestats has three modes: In quiet mode (-q), the exit status is 0 (success) if the file is fully cached. In normal mode, the number of cached vs. not-cached pages is printed. In verbose mode (-v), an actual map is printed out, where each page that is present in the cache is marked with x.

It looks like this:

$ cachestats -v ~/somefile.mp3
pages in cache: 85/114 (74.6%)  [filesize=453.5K, pagesize=4K]

cache map:
     0: |x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|
    32: |x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|
    64: |x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x|x| | | | | | | | | | | | |
    96: | | | | | | | | | | | | | | | | | |x|

Also, you can use vmstat 1 to view cache statistics.

For debugging purposes, you can specify a filename that nocache should log debugging messages to via the -D command line switch, e.g. use nocache -D /tmp/nocache.log โ€ฆ. Note that for simple testing the file /dev/stderr might be a good choice.

Example run

Without nocache, the file will be fully cached when you copy it somewhere:

$ ./cachestats ~/file.mp3
pages in cache: 154/1945 (7.9%)  [filesize=7776.2K, pagesize=4K]
$ cp ~/file.mp3 /tmp
$ ./cachestats ~/file.mp3
pages in cache: 1945/1945 (100.0%)  [filesize=7776.2K, pagesize=4K]

With nocache, the original caching state will be preserved.

$ ./cachestats ~/file.mp3
pages in cache: 154/1945 (7.9%)  [filesize=7776.2K, pagesize=4K]
$ ./nocache cp ~/file.mp3 /tmp
$ ./cachestats ~/file.mp3
pages in cache: 154/1945 (7.9%)  [filesize=7776.2K, pagesize=4K]

Limitations

The pre-loaded library tries really hard to catch all system calls that open or close a file. This happens by "hijacking" the libc functions that wrap the actual system calls. In some cases, this may fail, for example because the application does some clever wrapping. (That is the reason why __openat_2 is defined: GNU tar uses this instead of a regular openat.)

However, since the actual fadvise calls are performed right before the file descriptor is closed, this may not happen if they are left open when the application exits, although the destructor tries to do that.

There are timing issues to consider, as well. If you consider nocache cat <file>, in most (all?) cases the cache will not be restored. For discussion and possible solutions see http://lwn.net/Articles/480930/. My experience showed that in many cases you could "fix" this by doing the posix_fadvise call twice. For both tools nocache and cachedel you can specify the number using -n, like so:

$ nocache -n 2 cat ~/file.mp3

This actually only sets the environment variable NOCACHE_NR_FADVISE to the specified value, and the shared library reads out this value. If test number 3 in t/basic.t fails, then try increasing this number until it works, e.g.:

$ env NOCACHE_NR_FADVISE=2 make test

One could also consider that the fact pages are kept mean the kernel considers they are hot, and decide the overhead of allocating one byte per page for mincore and the actual mincore calls are not worth it when the kernel actually does keep some pages when it wants to.

In this case you can either run nocache with -f or set the NOCACHE_FLUSHALL environment variable to 1, e.g.:

$ nocache -f cat ~/file.mp3
$ env NOCACHE_FLUSHALL=1 make test

By default nocache will only keep track of file descriptors less than 1 million that are opened by your application, in order to bound its memory consumption. If you want to change this threshold, you can supply the environment variable NOCACHE_MAX_FDS and set it to a higher (or lower) value.

Alternate Approaches

If you have a fairly recent Linux kernel, you can also try to simply cage a cache-intensive application in a memory-limited cgroup. For example, I use the following command in the startup part of my backup script:

sudo env ppid=$$ sh -c '
    cgcreate -g memory:backup ;
    cgcreate -g blkio:backup ;
    echo 256M > /sys/fs/cgroup/memory/backup/memory.limit_in_bytes ;
    echo 100 > /sys/fs/cgroup/blkio/backup/blkio.weight ;
    echo $ppid > /sys/fs/cgroup/memory/backup/tasks ;
    echo $ppid > /sys/fs/cgroup/blkio/backup/tasks ;
'

More info: https://www.kernel.org/doc/Documentation/cgroup-v1/memory.txt

Acknowledgements

Most of the application logic is from Tobias Oetiker's patch for rsync http://insights.oetiker.ch/linux/fadvise.html. Note however, that rsync uses sockets, so if you try a nocache rsync, only the local process will be intercepted.

nocache's People

Contributors

feh avatar noushi avatar onlyjob avatar xxmail avatar iillyyaa avatar jwilk avatar cicku avatar martinetd avatar paulharris avatar cubicdaiya avatar

Watchers

James Cloos avatar

Recommend Projects

  • React photo React

    A declarative, efficient, and flexible JavaScript library for building user interfaces.

  • Vue.js photo Vue.js

    ๐Ÿ–– Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.

  • Typescript photo Typescript

    TypeScript is a superset of JavaScript that compiles to clean JavaScript output.

  • TensorFlow photo TensorFlow

    An Open Source Machine Learning Framework for Everyone

  • Django photo Django

    The Web framework for perfectionists with deadlines.

  • D3 photo D3

    Bring data to life with SVG, Canvas and HTML. ๐Ÿ“Š๐Ÿ“ˆ๐ŸŽ‰

Recommend Topics

  • javascript

    JavaScript (JS) is a lightweight interpreted programming language with first-class functions.

  • web

    Some thing interesting about web. New door for the world.

  • server

    A server is a program made to process requests and deliver data to clients.

  • Machine learning

    Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.

  • Game

    Some thing interesting about game, make everyone happy.

Recommend Org

  • Facebook photo Facebook

    We are working to build community through open source technology. NB: members must have two-factor auth.

  • Microsoft photo Microsoft

    Open source projects and samples from Microsoft.

  • Google photo Google

    Google โค๏ธ Open Source for everyone.

  • D3 photo D3

    Data-Driven Documents codes.