ESP32 Camera extension to record JPEGs to SD card as MJPEG files and playback to browser.
Files uploaded by FTP are optionally converted to AVI format to allow recordings to replay at correct frame rate on media players.
The MJPEG format contains the original JPEG images but displays them as a video. MJPEG playback is not inherently rate controlled, but the app attempts to play back at the MJPEG recording rate. MJPEG files can also be played on video apps or converted into rate controlled AVI or MKV files etc.
Saving a set of JPEGs as a single file is faster than as individual files and is easier to manage, particularly for small image sizes. Actual rate depends on quality and size of SD card and complexity and quality of images. A no-name 4GB SDHC labelled as Class 6 was 3 times slower than a genuine Sandisk 4GB SDHC Class 2. The following recording rates were achieved on a freshly formatted Sandisk 4GB SDHC Class 2 using SD_MMC 1 line mode on a AI Thinker OV2640 board, set to maximum JPEG quality and highest clock rate.
Frame Size | OV2640 camera max fps | mjpeg2sd max fps | Detection time ms |
---|---|---|---|
*96X96 | 50 | 45 | 15 |
QQVGA | 50 | 45 | 20 |
*QCIF | 50 | 45 | 30 |
HQVGA | 50 | 45 | 40 |
*240X240 | 50 | 45 | 55 |
QVGA | 50 | 40 | 70 |
CIF | 50 | 40 | 110 |
*HGVA | 50 | 40 | 130 |
VGA | 25 | 20 | 80 |
SVGA | 25 | 20 | 120 |
XGA | 6.25 | 5 | 180 |
*HD | 6.25 | 5 | 220 |
SXGA | 6.25 | 5 | 300 |
UXGA | 6.25 | 5 | 450 |
* Ony available with arduino-esp32
development release v1.0.5rc4
The ESP32 Cam module has 4MB of pSRAM which is used to buffer the camera frames and the construction of the MJPEG file to minimise the number of SD file writes, and optimise the writes by aligning them with the SD card sector size. For playback the MJPEG is read from SD into a multiple sector sized buffer, and sent to the browser as timed individual frames.
The SD card can be used in either MMC 1 line mode (default) or MMC 4 line mode. The MMC 1 line mode is practically as fast as MMC 4 line and frees up pin 4 (connected to onboard Lamp), and pin 12 which can be used for eg a PIR.
The MJPEG files are named using a date time format YYYYMMDD_HHMMSS, with added frame size, recording rate, duration and frame count, eg 20200130_201015_VGA_15_60_900.mjpeg, and stored in a per day folder YYYYMMDD.
The ESP32 time is set from an NTP server.
Note: arduino-esp32
stable release v1.0.4 is over a year old, since when improvements has been made to arduino-esp32
and esp32-camera
. To compile this extension
using the latest v1.0.5 development release candidate (assuming this is loaded in the Arduino IDE), comment out #define USE_v1.0.4
in ESP32-CAM_MJPEG2SD.ino
Download files into the Arduino IDE sketch location, removing -master
from the folder name.
The included sketch ESP32-CAM_MJPEG2SD.ino
is derived from the CameraWebServer.ino
example sketch included in the Arduino ESP32 library.
Additional code has been added to the original file app_httpd.cpp
to handle the extra browser options, and an additional filemjpeg2sd.cpp
contains the SD handling code. The web page content in camera_index.h
has been updated to include additional functions.
The face detection code has been removed to reduce the sketch size to allow OTA updates.
To set the recording parameters, additional options are provided on the camera index page, where:
Frame Rate
is the required frames per secondMin Frames
is the minimum number of frames to be captured or the file is deletedVerbose
if checked outputs additional logging to the serial monitor
An MJPEG recording is generated by holding a given pin high (kept low by internal pulldown when released).
The pin to use is:
- pin 12 when in 1 line mode
- pin 33 when in 4 line mode
An MJPEG recording can also be generated by the camera itself detecting motion as given in the Motion detection by Camera section below.
If recording occurs whilst also live streaming to browser, the frame rate will be slower.
To play back a recording, select the file using Select folder / file on the browser to select the day folder then the required MJPEG file. After selecting the MJPEG file, press Start Stream button to playback the recording. The recorded playback rate can be changed during replay by changing the FPS value. After playback finished, press Stop Stream button. If a recording is started during a playback, playback will stop.
The following functions are provided by @gemi254:
-
Entire folders or files within folders can be deleted by selecting the required file or folder from the drop down list then pressing the Delete button and confirming.
-
Entire folders or files within folders can be uploaded to a remote server via FTP by selecting the required file or folder from the drop down list then pressing the FTP Upload button.
-
The FTP, Wifi, and other parameters need to be defined in file
myConfig.h
, and can also be modified via the browser under Other Settings. -
Check internet connection and automatically reconnect if needed on power loss.
-
Added mdns name services in order to use
http://[Host Name]
instead of ip address -
Delete or ftp upload and delete oldest folder when card free space is running out.
SeeminCardFreeSpace
andfreeSpaceMode
inmjpeg2sd.cpp
Additional ancilliary functions:
- Enable Over The Air (OTA) updates - see
ota.cpp
- Add temperature sensor - see
ds18b20.cpp
- Add analog microphone support - see
avi.cpp
Browser functions only tested on Chrome.
An MJPEG recording can also be generated by the camera itself detecting motion using the motionDetect.cpp
file.
JPEG images of any size are retrieved from the camera and 1 in N images are sampled on the fly for movement by decoding them to very small grayscale bitmap images which are compared to the previous sample. The small sizes provide smoothing to remove artefacts and reduce processing time.
For movement detection a high sample rate of 1 in 2 is used. When movement has been detected, the rate for checking for movement stop is reduced to 1 in 10 so that the JPEGs can be captured with only a small overhead. The Detection time ms table shows typical time in millis to decode and analyse a frame retrieved from the OV2640 camera.
To enable motion detection by camera, in mjpeg2sd.cpp
set #define USE_MOTION true
Additional options are provided on the camera index page, where:
Motion Sensitivity
sets a threshold for movement detection, higher is more sensitive.Show Motion
if enabled and the Start Stream button pressed, shows images of how movement is detected for calibration purposes. Gray pixels show movement, which turn to black if the motion threshold is reached.
The motionDetect.cpp
file contains additional documented monitoring parameters that can be modified.