bg4czu / mmdvm_hs_dual_hat

Duplex variant of MMDVM_HS_Hat

MMDVM_HS_Dual_Hat

Duplex variant of MMDVM_HS_Hat DB9MAT DF2ET DO7EN

This PCB uses the MMDVM_HS by Andy CA6JAU. It has two ADF7021 onboard and allows for duplex operation with two time slots on DMR.

Revisions

Revision 1.0

Initial release.

Revision 1.1

LEDs D4 and D5 interchanged to align with scan order. Solder jumper JP1 was added. It can be closed if the board is used on Raspberry Pi only. It ties BOOT1 to GND. BOOT0 is controlled via GPIO. The 2x3 pin header can be unpopulated in this case to save space. We placed two coils on U1 and U2 for experiments with extended VCO. These are L11 and L12 and they are optional and do not need to be inserted for UHF use. Testpoints TP1 and TP2 on backside allows the demodulator output SNR to be measured with #define TEST_DAC compiled firmware.

This version is not recommended for (re-)production!

Revision 1.2

An accidentially deleted 3v3 wire has been added back to the PCB layout. BOM, Mouser cart and stencil stay the same as for rev1.1.

BOM

Mouser cart for rev1.0 is here.

This is the Mouser cart for rev1.1. L11 and L12 are optional.

Firmware installation

The device can be used on top on a RPi attached via the GPIO port or standalone and connected via USB. Both variants require different handling of compiling and uploading the firmware. The USB connection requires firmware with bootloader support whereas the GPIO version does not.

For USB connection a bootloader has to be installed initally. This requires STlink connection. After that is done the MMDVM_HS firmware upgrade can be done via the USB connection. The STlink connection can be used as fallback if wrongly configured firmware was installed for example.

Install the firmware with bootloader support for USB connection

If you want to use the device via USB port you have to install a bootloader and build the firmware with bootloader support. As the raw device cannot be used with USB you have to use a USB-serial adapter or STlink device. Using STlink this can be done as follows:

user@host:/opt/MMDVM_HS$ make stlink-bl 
././STM32F10X_Lib/utils/linux64/st-flash write ./STM32F10X_Lib/utils/bootloader/generic_boot20_pc13.bin 0x8000000
2018-03-02T10:01:04 INFO src/usb.c: -- exit_dfu_mode
2018-03-02T10:01:04 INFO src/common.c: Loading device parameters....
2018-03-02T10:01:04 INFO src/common.c: Device connected is: F1 Medium-density device, id 0x20036410
2018-03-02T10:01:04 INFO src/common.c: SRAM size: 0x5000 bytes (20 KiB), Flash: 0x10000 bytes (64 KiB) in pages of 1024 bytes
2018-03-02T10:01:04 INFO src/common.c: Attempting to write 7160 (0x1bf8) bytes to stm32 address: 134217728 (0x8000000)
Flash page at addr: 0x08001800 erased
2018-03-02T10:01:04 INFO src/common.c: Finished erasing 7 pages of 1024 (0x400) bytes
2018-03-02T10:01:04 INFO src/common.c: Starting Flash write for VL/F0/F3 core id
2018-03-02T10:01:04 INFO src/common.c: Successfully loaded flash loader in sram
  6/6 pages written
2018-03-02T10:01:05 INFO src/common.c: Starting verification of write complete
2018-03-02T10:01:05 INFO src/common.c: Flash written and verified! jolly good!
././STM32F10X_Lib/utils/linux64/st-flash write bin/mmdvm_f1bl.bin 0x8002000
2018-03-02T10:01:05 INFO src/common.c: Loading device parameters....
2018-03-02T10:01:05 INFO src/common.c: Device connected is: F1 Medium-density device, id 0x20036410
2018-03-02T10:01:05 INFO src/common.c: SRAM size: 0x5000 bytes (20 KiB), Flash: 0x10000 bytes (64 KiB) in pages of 1024 bytes
2018-03-02T10:01:05 INFO src/common.c: Attempting to write 55016 (0xd6e8) bytes to stm32 address: 134225920 (0x8002000)
Flash page at addr: 0x0800f400 erased
2018-03-02T10:01:07 INFO src/common.c: Finished erasing 54 pages of 1024 (0x400) bytes
2018-03-02T10:01:07 INFO src/common.c: Starting Flash write for VL/F0/F3 core id
2018-03-02T10:01:07 INFO src/common.c: Successfully loaded flash loader in sram
 53/53 pages written
2018-03-02T10:01:12 INFO src/common.c: Starting verification of write complete
2018-03-02T10:01:13 INFO src/common.c: Flash written and verified! jolly good!

The device should now be usable as /dev/ttyACMx.

If you want to update the MMDVM_HS firmware itself later on via USB you can use the dfu upload method. The settings in Config.h are:

#define MMDVM_HS_DUAL_HAT_REV10
#define ENABLE_ADF7021
#define DUPLEX
#define ADF7021_14_7456
#define STM32_USB_HOST
#define ENABLE_SCAN_MODE

Optionally:

#define SEND_RSSI_DATA
#define SERIAL_REPEATER

Compile the firmware with "make bl" and then:

user@host:/opt/MMDVM_HS$ sudo make dfu devser=/dev/ttyACM3
././STM32F10X_Lib/utils/linux64/upload-reset /dev/ttyACM3 750
././STM32F10X_Lib/utils/linux64/dfu-util -D bin/mmdvm_f1bl.bin -d 1eaf:0003 -a 2 -R -R
dfu-util 0.7

Copyright 2005-2008 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2012 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to [email protected]

Filter on vendor = 0x1eaf product = 0x0003
Opening DFU capable USB device... ID 1eaf:0003
Run-time device DFU version 0110
Found DFU: [1eaf:0003] devnum=0, cfg=1, intf=0, alt=2, name="STM32duino bootloader v1.0  Upload to Flash 0x8002000"
Claiming USB DFU Interface...
Setting Alternate Setting #2 ...
Determining device status: state = dfuIDLE, status = 0
dfuIDLE, continuing
DFU mode device DFU version 0110
Device returned transfer size 1024
No valid DFU suffix signature
Warning: File has no DFU suffix
bytes_per_hash=1100
Copying data from PC to DFU device
Starting download: [##################################################] finished!
state(8) = dfuMANIFEST-WAIT-RESET, status(0) = No error condition is present
Done!
Resetting USB to switch back to runtime mode

Compile and upload manually for GPIO connection

For specific details about the firmware installation, check these instructions. The process is similar to the installation on the ZumSpot Pi. You can make use of the preconfigured scripts in MMDVM_HS. Editing Config.h by hand requires these settings:

Enable the following settings in Config.h:

#define MMDVM_HS_DUAL_HAT_REV10
#define ENABLE_ADF7021
#define DUPLEX
#define ADF7021_14_7456
#define STM32_USART1_HOST
#define ENABLE_SCAN_MODE

Optionally:

#define SEND_RSSI_DATA
#define SERIAL_REPEATER

Build the firmware:

make

Make sure the two BOOT jumpers are set as follows:

BOOT0: completey removed
BOOT1: set to BOOT 1 -

And finally upload the firmware to the MMDVM_HS_Dual_Hat:

sudo make mmdvm_hs_dual_hat

Update within Pi-Star

Currently not possible. Will probably follow.

License

This project is released under the Creative Commons Attribution-NonCommercial-ShareAlike 3.0 (CC-BY-NC-SA 3.0, https://creativecommons.org/licenses/by-nc-sa/3.0/) license. You may edit and share it as you like, as long as credit is given and the license is not changed. You can build as many boards for you and your friends as you like and you can even sell it to them to cover your costs, however it is strictly forbidden to turn this into a commercial product! You are not allowed to build and sell these boards for profit!