Before installing MapR it is critically important to validate the hardware and software that MapR will be dependent on. Doing so will verify that items like disks, CPUs and NICs are performing as expected and the benchmark metric logged. Doing so will also verify that many of the basic OS configurations and packages are in the required state and that state is also recorded in an output log.
Please use the steps below to test CPU/RAM, disk, and networking performance as well as to verify that your cluster meets MapR installation requirements. Pre-install tests should be run before installing MapR. Post-install tests should be run after installing the MapR software and configuring it. Post-install tests help assure that the cluster is in good working order and ready to hand over to your production team.
Install clustershell (rpm available via EPEL) on a machine with
password-less ssh to all other cluster nodes. If using a non-root
account, then non-root account must have password-less sudo rights
configured in /etc/sudoers. Update the file
/etc/clustershell/groups.d/local.cfg or /etc/clustershell/groups
to include an entry for "all" matching a pattern or patterns of
host names in your cluster.
For example;
all: node[0-10]
Verify clush works correctly by running:
clush -a date
Compare results with:
clush -ab date
Complete documentation for clush and clustershell can be found here: http://clustershell.readthedocs.org/en/latest/tools/clush.html
If you don't find clustershell in EPEL, you may be able to download rpm here:
http://mirror.math.princeton.edu/pub/epel/6/x86_64/clustershell-1.7.2-1.el6.noarch.rpm
Next, download and extract the cluster-validation package with a command like this:
curl -L -o cluster-validation.tgz http://github.com/MapRPS/cluster-validation/tarball/master
Extract with tar in /root or your home folder and rename the top level folder like this:
mv jbenninghoff-cluster-validation-* cluster-validation
or
mv cluster-validation-* cluster-validation
Copy the cluster-validation folder to all nodes in the cluster. The clush command simplifies this:
clush -a --copy /path.../cluster-validation
clush -Ba ls /path.../cluster-validation # confirm that all nodes have the utilties
Run cluster-audit.sh as root to verify that all nodes have met the MapR installation requirements. Run:
cd /root/cluster-validation/
pre-install/cluster-audit.sh | tee cluster-audit.log
on the node where clush has been installed and configured to access
all cluster nodes. Examine the log for inconsistency among any nodes.
Do not proceed until all inconsistencies have been resolved and all
requirements such as missing rpms, Java version, etc. have been met.
Please send the output of the cluster-audit.log back to us.
NOTE: cluster-audit.sh is designed for physical servers.
Virtual Instances in cloud environments (eg Amazon, Google, or
OpenStack) may generate confusing responses to some specific
commands (eg dmidecode). In most cases, these anomolies are
irrelevant.
Use the network test to validate network bandwidth. This will take about two minutes or so to run and produce output so be patient. The script will use clush to collect the IP addresses of all the nodes and split the set in half, using first half as servers and the second half as clients. The half1 and half2 arrays in the network-test.sh script can be manually defined as well. There are command line options for sequential mode and to run iperf as well. Run:
cd /root/cluster-validation/
pre-install/network-test.sh | tee network-test.log
on the node where clush has been installed and configured. Expect about 90% of peak bandwidth for either 1GbE or 10GbE networks:
1 GbE ==> ~115 MB/sec
10 GbE ==> ~1150 MB/sec
Use the stream59 benchmark to test memory performance. This test will take about a minute or so to run. It can be executed in parallel on all the cluster nodes with the command:
cd /root/cluster-validation/
clush -Ba "$PWD/pre-install/memory-test.sh | grep -e ^Func -e ^Triad" | tee memory-test.log
System memory bandwidth is determined by speed of DIMMs, number of memory channels and to a lesser degree by CPU frequency. Current generation Xeon based servers with eight or more 1600MHz DIMMs can deliver 70-80GB/sec Triad results. Previous generation Xeon cpus (Westmere) can deliver ~40GB/sec Triad results. You can look up the cluster CPU as shown by cluster-audit.sh, at http://ark.intel.com/. The technical specifications for the CPU model will include the Max Memory Bandwidth (per CPU socket). Servers typically have two CPU sockets, so doubling that Max Bandwidth shown will give you the Max Memory Bandwidth for the server. The measured Stream Triad result from memory-test.log can then be compared to the Max Memory Bandwidth of the server. The Triad bandwidth should be approximately 75-85% of the Max Memory Bandwidth of the server.
Use the iozone benchmark to test disk performance. This process is destructive to disks that are tested, so make sure that you have not installed MapR nor have any needed data on those spindles. The script as shipped will ONLY list out the disks to be tested. When run with no arguments, this script outputs a list of unused disks. After carefully examining this list, run again with --destroy as the argument ('disk-test.sh --destroy') to run the destructive IOzone tests on all unused disks.
The test can be run in parallel on all nodes with:
cd /root/cluster-validation/
clush -ab "$PWD/pre-install/disk-test.sh"
clush -ab "$PWD/pre-install/summIOzone.sh"
Current generation (2012+) 7200 rpm SATA drives can report 100-150MB/sec sequential read and write throughput. SAS, SSD and NVMe drives can report from 200MB/sec to nearly 2GB/sec for NVMe drives as measured by sequential iozone or fio tests on the raw device. By default, the disk test only uses a 4GB data set size in order to finish quickly. Consider using a larger size to measure disk throughput more thoroughly. Doing so will typically require hours to run which could be done overnight if your schedule allows. For large numbers of nodes and disks there is a summIOzone.sh script that can help provide a summary of disk-test.sh output using clush.
clush -ab /root/cluster-validation/pre-install/summIOzone.sh
When all subsystem tests have passed and met expectations, there is an example install script in the pre-install folder that can be modified and used for a scripted install by experienced users.
pre-install/mapr-install.sh -h
Otherwise, follow the instructions from the mapr web site: http://maprdocs.mapr.com/home/install.html
Post installation tests are in the post-install folder. The primary tests are RWSpeedTest and TeraSort. Scripts to run each are provided in the folder. Read the scripts for additional info.
A script to create a benchmarks volume mkBMvol.sh is provided.
Be sure to create the benchmarks volume before running any of the
post install benchmarks.
NOTE: The TeraSort benchmark (executed by runTeraGenSort.sh) will likely
require tuning for each specific cluster. At a minimum, pass integer
arguments in powers of 2 (e.g. 4, 8, etc) to the script to increase the
number of reduce tasks per node up to the maximum reduce slots available on
your cluster. Experiment with the -D options as needed.
The post-install folder also contains a mapr-audit.sh script which can be run to provide an audit log of the MapR configuration. The script contains a useful set of example maprcli commands. There are also example install, upgrade and un-install options to mapr-install.sh that leverage clush to run quickly on an entire set of nodes or cluster. Some of the scripts will not run without editing, so read the scripts carefully to understand how to edit them with site specific info. All scripts support the -h option to show help on usage.
/John Benninghoff
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent