Comments (9)
Hi Pam,
I have been going through the wiki and I think everything I did is contained there. I can also see the USB from l1ts-rct-02, so it is somehow connected.
Can it be a code issue? Have you updated to the latest code in the repository? I will be there tomorrow morning, since I still have the version of the code that we used before Evan left untouched in my setup we can test it to see if this was caused by a change.
(Just to know, after what command does it stop?)
Maria
from cms-calo-layer1.
The XMD command run on l1ts-rct-01 (the JTAG controller going to the CTP6 is connected to that PC), do I instead need to use the USB (from the hub) on l1ts-rct-02? Anyhow, here is the full text:
make upload
echo "connect mb mdm -debugdevice deviceNr 2; rst; connect mb mdm -debugdevice deviceNr 2; dow payload.elf; run" | xmd
Xilinx Microprocessor Debugger (XMD) Engine
Xilinx EDK 14.4 Build EDK_P.49d
Copyright (c) 1995-2012 Xilinx, Inc. All rights reserved.
XMD%
XMD% ERROR: Failed to Open JTAG Cable
Cable target is not connected to the host
from cms-calo-layer1.
You're right, this should be done from l1ts-rct-01 - sorry.
I do get the same exact error with my installation, so it is not a change in code.
Was any cable moved last week in the operations?
from cms-calo-layer1.
I put the front panel on, but then took it off again yesterday thinking that it was still interfering. So there were a couple of power cycles.
from cms-calo-layer1.
I did make sure there were clocks coming from the AMC13 again, following instructions that I had been e-mailed, now they are copied to the CTP6 page.
from cms-calo-layer1.
So, did you guys figure this one out ? It might be that the drivers on the pc are corrupted, so you might have to install them again. I had this problem here in Chmbrln with the pc connected to CTP6. The driver install script is in here,
/PATH/TO//Xilinx/14.4/ISE_DS/common/bin/lin64/install_script/install_drivers/install_drivers
from cms-calo-layer1.
Hi Tapas,
Thanks!
That fixed it.
In the README of the directory you sent (/opt/Xilinx/14.4/ISE_DS/common/bin/lin/install_script/install_drivers/readme.txt) it explains that:
NOTE: By default, access to windrvr6 is restricted to root only. This step grants group and user access to the driver. However, if you reboot your system, access to the driver will revert back to root-only and you will have to repeat step #7 (you do not have to rerun the installation script).
(7. Change permissions on the USB / PC4 driver by typing: chmod 666 /dev/windrvr6.)
I changed the permissions of that file and now I can "make upload".
Maria
from cms-calo-layer1.
I tested the full set of instructions and it worked on my side.
I included the problem (&solution) in the CTP6 wiki for instructions (https://github.com/uwcms/cms-calo-layer1/wiki/The-CTP6#known-problems--solutions)
@pklabbers , did you try? Can I close the issue?
Maria
from cms-calo-layer1.
Hi Maria,
I'll give it a shot again tomorrow, and then close this if it works.
Thanks for all the help,
Pam
from cms-calo-layer1.
Related Issues (20)
- Test SPIStream via oRSC inter-FPGA echo test HOT 2
- caen::write() does not do what we think HOT 2
- oRSC Back-End Doesn't Reach "main()" HOT 2
- Ensure we can read out link status from the CTP6 FE at 904 HOT 5
- /opt/AMC13/ecad_activate_amc13.sh needs python 2.6 at 904 HOT 3
- Validate instructions on updating BSPs using Xilinx GUI HOT 1
- Document how to recover from Xilinx "JTAG Cable not Found" error HOT 5
- oRSC Locks up VME HOT 32
- update issue #4 ... readout link status @ chmbln HOT 33
- Address items requested by L1 SW code review
- oRSC FE SPI XIntc_Connect Jumps to Command 'DEADBEEF' HOT 18
- Can't make blinky lights on oRSC HOT 3
- VMEStream Echo Test HOT 9
- Write standalone uart backend application for oRSC HOT 4
- oRSC uart ECHO test (working at Chmberlin) HOT 4
- ASIO reported a Timeout in TCP callback HOT 10
- Put VMEStream in cms-calo-layer1 package HOT 4
- Write orsc_fe_vmestream_echo_test and validate VMEStream HOT 6
- Write oRSC BE VMEStream -> SPIStream code HOT 7
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from cms-calo-layer1.