Can't compile driver about rtl8192eu-linux-driver

[kkaja123]

I believe you will need to edit the platform configuration in the Makefile.

Open the Makefile and change CONFIG_PLATFORM_I386_PC to n and change CONFIG_PLATFORM_ARM_RPI to y. And just to be sure, run make clean after changing those options (although this probably isn't necessary).

[Dschogo]

If the rpi is running 64bit use aarch64, its not called rpi but thats just naming. RPI defaults to 32bit i think (kernel 6.1.21-b8+ - rpi3b+)
CONFIG_PLATFORM_ARM_RPI = n
CONFIG_PLATFORM_ARM_AARCH64 = y

Click me for Makefile

EXTRA_CFLAGS += $(USER_EXTRA_CFLAGS)

##################### Optimization Flags ##########################
EXTRA_CFLAGS += -O2
##################### Compile-time Warnings #######################
EXTRA_CFLAGS += -Wno-unused-variable
EXTRA_CFLAGS += -Wno-unused-label
EXTRA_CFLAGS += -Wno-unused-function

GCC_VER_49 := $(shell echo `$(CC) -dumpversion | cut -f1-2 -d.` \>= 4.9 | bc )
ifeq ($(GCC_VER_49),1)
endif

EXTRA_CFLAGS += -I$(src)/include

EXTRA_LDFLAGS += --strip-debug

CONFIG_AUTOCFG_CP = n

########################## WIFI IC ############################
CONFIG_MULTIDRV = n
CONFIG_RTL8188E = n
CONFIG_RTL8812A = n
CONFIG_RTL8821A = n
CONFIG_RTL8192E = y
CONFIG_RTL8723B = n
CONFIG_RTL8814A = n
CONFIG_RTL8723C = n
CONFIG_RTL8188F = n
CONFIG_RTL8188GTV = n
CONFIG_RTL8822B = n
CONFIG_RTL8723D = n
CONFIG_RTL8821C = n
CONFIG_RTL8710B = n
CONFIG_RTL8192F = n
######################### Interface ###########################
CONFIG_USB_HCI = y
CONFIG_PCI_HCI = n
CONFIG_SDIO_HCI = n
CONFIG_GSPI_HCI = n
########################## Features ###########################
CONFIG_MP_INCLUDED = y
# Exposes power saving features to the system if the wireless adapter supports them.
# Say "y" here if unsure.
CONFIG_POWER_SAVING = y
# Automatically suspends the wireless adapter during inactivity.
# Say "n" here if unsure. It may save a small amount of power, while introducing instability.
CONFIG_USB_AUTOSUSPEND = n
CONFIG_HW_PWRP_DETECTION = n
CONFIG_BT_COEXIST = y
CONFIG_INTEL_WIDI = n
CONFIG_WAPI_SUPPORT = n
CONFIG_EFUSE_CONFIG_FILE = y
CONFIG_EXT_CLK = n
CONFIG_TRAFFIC_PROTECT = n
CONFIG_LOAD_PHY_PARA_FROM_FILE = y
CONFIG_TXPWR_BY_RATE = y
CONFIG_TXPWR_BY_RATE_EN = n
CONFIG_TXPWR_LIMIT = y
CONFIG_TXPWR_LIMIT_EN = n
CONFIG_RTW_CHPLAN = 0xFF
CONFIG_RTW_ADAPTIVITY_EN = disable
CONFIG_RTW_ADAPTIVITY_MODE = normal
CONFIG_SIGNAL_SCALE_MAPPING = n
# Enables Protected Management Frames (PMF). Say "y" here if unsure.
# This is required for TKIP/CCMP support.
CONFIG_80211W = y
CONFIG_REDUCE_TX_CPU_LOADING = n
CONFIG_BR_EXT = y
# Compile in TDLS (Tunneled Direct Link Setup) support.
# Part of the IEEE 802.11z standard. Say "n" here if unsure. 
CONFIG_TDLS = n
# Compile in monitor-mode support. Say "y" here if unsure.
# Some userspace applications may complain if the wireless adapter doesn't have this.
# Used mainly to grab packets from a wireless network.
CONFIG_WIFI_MONITOR = y
CONFIG_MCC_MODE = n
CONFIG_APPEND_VENDOR_IE_ENABLE = n
CONFIG_RTW_NAPI = y
# GRO is not usually beneficial in lossy or slow (<1GB/s) networks, such as wireless.
# Setting "n" here will prevent queue management from having to "peel" packets, at no performance cost.
# Further reading: https://www.bufferbloat.net/projects/codel/wiki/Cake/#tso-gso-gro-peeling
CONFIG_RTW_GRO = n
CONFIG_RTW_NETIF_SG = y
# Try to offload checksum operations to the wireless adapter. Say "n" if unsure, the CPU usually does a better job at this.
# Say "y" here if this is an embedded device.
CONFIG_TX_CSUM_OFFLOAD = n
CONFIG_RTW_IPCAM_APPLICATION = n
CONFIG_RTW_REPEATER_SON = n
CONFIG_RTW_WIFI_HAL = n
CONFIG_ICMP_VOQ = n
CONFIG_IP_R_MONITOR = n #arp VOQ and high rate
########################## Debug ###########################
# Say "y" here to have the driver output debugging messages. Not intended for normal use.
CONFIG_RTW_DEBUG = n
# Default log level is 2, which only displays errors.
# Available levels = none(0), always(1), error(2), warning(3), info(4), debug(5), max(6)
CONFIG_RTW_LOG_LEVEL = 2
######################## Wake On Lan ##########################
CONFIG_WOWLAN = n
#bit2: deauth, bit1: unicast, bit0: magic pkt.
CONFIG_WAKEUP_TYPE = 0x7
#bit0: disBBRF off, #bit1: Wireless remote controller (WRC)
CONFIG_SUSPEND_TYPE = 0
CONFIG_WOW_STA_MIX = n
CONFIG_GPIO_WAKEUP = n
CONFIG_WAKEUP_GPIO_IDX = default
CONFIG_HIGH_ACTIVE_DEV2HST = n
######### only for USB #########
CONFIG_ONE_PIN_GPIO = n
CONFIG_HIGH_ACTIVE_HST2DEV = n
CONFIG_PNO_SUPPORT = n
CONFIG_PNO_SET_DEBUG = n
CONFIG_AP_WOWLAN = n
######### Notify SDIO Host Keep Power During Syspend ##########
CONFIG_RTW_SDIO_PM_KEEP_POWER = y
###################### MP HW TX MODE FOR VHT #######################
CONFIG_MP_VHT_HW_TX_MODE = n
###################### Platform Related #######################
CONFIG_PLATFORM_ARM_RPI = n
CONFIG_PLATFORM_ARM_AARCH64 = y
CONFIG_PLATFORM_I386_PC = n
CONFIG_PLATFORM_ANDROID_X86 = n
CONFIG_PLATFORM_ANDROID_INTEL_X86 = n
CONFIG_PLATFORM_JB_X86 = n
CONFIG_PLATFORM_ARM_S3C2K4 = n
CONFIG_PLATFORM_ARM_PXA2XX = n
CONFIG_PLATFORM_ARM_S3C6K4 = n
CONFIG_PLATFORM_MIPS_RMI = n
CONFIG_PLATFORM_RTD2880B = n
CONFIG_PLATFORM_MIPS_AR9132 = n
CONFIG_PLATFORM_RTK_DMP = n
CONFIG_PLATFORM_MIPS_PLM = n
CONFIG_PLATFORM_MSTAR389 = n
CONFIG_PLATFORM_MT53XX = n
CONFIG_PLATFORM_ARM_MX51_241H = n
CONFIG_PLATFORM_FS_MX61 = n
CONFIG_PLATFORM_ACTIONS_ATJ227X = n
CONFIG_PLATFORM_TEGRA3_CARDHU = n
CONFIG_PLATFORM_TEGRA4_DALMORE = n
CONFIG_PLATFORM_ARM_TCC8900 = n
CONFIG_PLATFORM_ARM_TCC8920 = n
CONFIG_PLATFORM_ARM_TCC8920_JB42 = n
CONFIG_PLATFORM_ARM_TCC8930_JB42 = n
CONFIG_PLATFORM_ARM_RK2818 = n
CONFIG_PLATFORM_ARM_RK3066 = n
CONFIG_PLATFORM_ARM_RK3188 = n
CONFIG_PLATFORM_ARM_URBETTER = n
CONFIG_PLATFORM_ARM_TI_PANDA = n
CONFIG_PLATFORM_MIPS_JZ4760 = n
CONFIG_PLATFORM_DMP_PHILIPS = n
CONFIG_PLATFORM_MSTAR_TITANIA12 = n
CONFIG_PLATFORM_MSTAR = n
CONFIG_PLATFORM_SZEBOOK = n
CONFIG_PLATFORM_ARM_SUNxI = n
CONFIG_PLATFORM_ARM_SUN6I = n
CONFIG_PLATFORM_ARM_SUN7I = n
CONFIG_PLATFORM_ARM_SUN8I_W3P1 = n
CONFIG_PLATFORM_ARM_SUN8I_W5P1 = n
CONFIG_PLATFORM_ACTIONS_ATM702X = n
CONFIG_PLATFORM_ACTIONS_ATV5201 = n
CONFIG_PLATFORM_ACTIONS_ATM705X = n
CONFIG_PLATFORM_ARM_SUN50IW1P1 = n
CONFIG_PLATFORM_ARM_RTD299X = n
CONFIG_PLATFORM_ARM_LGE = n
CONFIG_PLATFORM_ARM_SPREADTRUM_6820 = n
CONFIG_PLATFORM_ARM_SPREADTRUM_8810 = n
CONFIG_PLATFORM_ARM_WMT = n
CONFIG_PLATFORM_TI_DM365 = n
CONFIG_PLATFORM_MOZART = n
CONFIG_PLATFORM_RTK119X = n
CONFIG_PLATFORM_RTK119X_AM = n
CONFIG_PLATFORM_RTK129X = n
CONFIG_PLATFORM_RTK390X = n
CONFIG_PLATFORM_NOVATEK_NT72668 = n
CONFIG_PLATFORM_HISILICON = n
CONFIG_PLATFORM_HISILICON_HI3798 = n
CONFIG_PLATFORM_NV_TK1 = n
CONFIG_PLATFORM_NV_TK1_UBUNTU = n
CONFIG_PLATFORM_RTL8197D = n
CONFIG_PLATFORM_AML_S905 = n
CONFIG_PLATFORM_ZTE_ZX296716 = n

########### CUSTOMER ################################
CONFIG_CUSTOMER_HUAWEI_GENERAL = n

CONFIG_DRVEXT_MODULE = n

export TopDIR ?= $(shell pwd)

[CGarces]

@stefanlk use suggestion from last comment.