Error: connection refused about android-bluez-ime

[GoogleCodeExporter]

It's an icontrolpad

Original comment by [email protected] on 26 Jun 2011 at 3:09

[GoogleCodeExporter]

Have you ensured the the iControlPad is in SSP mode (page 6):
http://www.icontrolpad.com/downloads/icp_manual3.pdf

Hold the Y button down when the iControlPad is turned off, and then press and 
hold the Start button to power on the iControlPad.

If it still does not work, can you send me a logcat message (while attempting 
to connect):
https://market.android.com/details?id=org.jtb.alogcat

Original comment by [email protected] on 26 Jun 2011 at 10:00

[GoogleCodeExporter]

[deleted comment]

[GoogleCodeExporter]

Doesn't connect emailed you log.

Original comment by [email protected] on 29 Jun 2011 at 12:09

[GoogleCodeExporter]

Doesn't connect emailed you log.

Original comment by [email protected] on 29 Jun 2011 at 12:09

[GoogleCodeExporter]

Doesn't connect emailed you log.

Original comment by [email protected] on 29 Jun 2011 at 12:09

[GoogleCodeExporter]

I have not received a log file?

Original comment by [email protected] on 29 Jun 2011 at 6:45

[GoogleCodeExporter]

I sent the cat log again.  I hope you get it this time.  I think I sent it
right.  Thank you, for your help

Richard Pew

Original comment by [email protected] on 30 Jun 2011 at 3:26

[GoogleCodeExporter]

I have received the log file, I'll look it over and see what I can do.

Original comment by [email protected] on 30 Jun 2011 at 8:07

[GoogleCodeExporter]

Thank you.

Original comment by [email protected] on 30 Jun 2011 at 12:04

[GoogleCodeExporter]

I had this same problem with my iCP.  I tried many different methods to get 
this to work again.  What I think worked in the end was doing the full reset - 
hold a,b,x,y while pressing start from off.  Then making it go to another mode, 
in my case HID Gamepad - hold x,y while pressing start from boot.  Finally, 
bring it back to SPP mode - hold y while pressing start from boot.  Key 
sequences are in the iCP manual.

I could tell that it wasn't getting into SPP mode because I could pair AND 
connect on my 3.1 Xoom.  One of the characteristics of SPP mode is only being 
able to pair.  

Good luck and keep trying.  I think it's an iCP problem not Bluez.

Original comment by [email protected] on 8 Jul 2011 at 4:21

[GoogleCodeExporter]

Thank you.

refused

Original comment by [email protected] on 8 Jul 2011 at 4:25

[GoogleCodeExporter]

Did you get it working?
I finally got around to looking at the log, and it seems to actually connect 
sometimes, but other times not.

Can you connect with your PC ? Can you connect with another Android app that 
supports iControlPad? (i.e.: 
https://market.android.com/details?id=com.explusalpha.Snes9x)

Original comment by [email protected] on 13 Jul 2011 at 7:33

• Changed state: Started

[GoogleCodeExporter]

I can't get it to connect to my Apple.

Original comment by [email protected] on 13 Jul 2011 at 12:14

[GoogleCodeExporter]

Ok, if it does not connect to anything, I think your iControlPad may be 
defective?

Original comment by [email protected] on 15 Jul 2011 at 7:32

[GoogleCodeExporter]

Is this still an issue?

Original comment by [email protected] on 15 Dec 2011 at 2:45

[GoogleCodeExporter]

No

Original comment by [email protected] on 15 Dec 2011 at 2:50

[GoogleCodeExporter]

cool, I'll close this issue

Original comment by [email protected] on 15 Dec 2011 at 3:45

• Changed state: Done