Comments (6)
Has anyone answered this?
from fysetc-spider.
I have the same problem on my Spider/Klipper ... only FAN0 correctly works with 24V, the other two don't.
My problem was a bad connection in the toolhead pcb not making contact with the fan V-
pin properly.
from fysetc-spider.
I only have problems with FAN2.
0 and 1 works fine. All on 24V.
Fan2 won't start. Have testet several settings.
from fysetc-spider.
I, too, am only having issues with FAN2. using the Fysetc kit w/ supplied 24V fans. tried the jumper/connector first, then just soldered the wires directly. haven't checked voltage yet. Might end up just hot wiring these to supply voltage...
from fysetc-spider.
So I too am having fan issues with my spider board purchased through the AliExpress fysetc store.
First the boot loader it came with somehow didn’t allow usb or uart communication. Flashing the boot loader they have here got usb and uart working.
Anyway the fans.
Fan0 is connected to my hot end fan and jumpered to 12v.
My print config is copied from here as well with some minor changes but the pins are correct from what I can tell.
At first Fan1 wasn’t working. It’s my parts fan. 24v
Changing printer.cfg to below worked. I’ll tweak as needed.
[fan1]
Pb1
But Fan0 nothing.
I’ve tried various config changes and no voltage output.
Also I’ve noticed when I apply some pressure around the fan0 connector I can hear a faint electric pop. It does it with the fans unplugged to.
Could my board have an internal short?
from fysetc-spider.
So I too am having fan issues with my spider board purchased through the AliExpress fysetc store. First the boot loader it came with somehow didn’t allow usb or uart communication. Flashing the boot loader they have here got usb and uart working. Anyway the fans. Fan0 is connected to my hot end fan and jumpered to 12v. My print config is copied from here as well with some minor changes but the pins are correct from what I can tell. At first Fan1 wasn’t working. It’s my parts fan. 24v Changing printer.cfg to below worked. I’ll tweak as needed. [fan1] Pb1
But Fan0 nothing. I’ve tried various config changes and no voltage output.
Also I’ve noticed when I apply some pressure around the fan0 connector I can hear a faint electric pop. It does it with the fans unplugged to. Could my board have an internal short?
Fan0 may not be coming on due to normal behavior. Shame on me for not noticing the extruder fan behavior below 50c
But my board makes an electrical popping noise if I apply a small amount of pressure around the FAN0 connector and its mosfet. Sounds like the layers are shorting to each other. Its consistent and repeatable. Nothing is loose.
from fysetc-spider.
Related Issues (20)
- 2.3 wont re-flash or upload bootloader HOT 1
- Spider 2.2 Data and 5V pin for Disco on a stick and StealthBurner LEDs
- Stepper motors not moving at all with Marlin
- Spider 3.0 documentation? HOT 1
- Unable to read tmc uart 'stepper_x' register MSCNT HOT 4
- Spider 2.3 Running Very Hot HOT 2
- spider 2.3_YMAX vs BLTOUCH
- Spider V2.2/klipper sensorless homing issue HOT 5
- Tmc2209 Unable to read tmc uart 'stepper_z HOT 5
- Water flow sensor HOT 1
- Spider 3.0 sensorless homing HOT 3
- TMC stepper_x failed to init: Unable to write tmc spi 'stepper_x' register GLOBALSCALER, TMC5160 on Spider 2.3
- Spider 3.0 Stepper Stuttering on Power Up HOT 16
- Spider v2.3 flash firmware and bootloader - jumpering for dfu-util HOT 2
- Spider v2.3; USB problems; no MCU id. HOT 2
- FYSETC Mini 12864 Panel 2.1 with Spider 3.0 and Marlin firmware
- I cannot flash bootloader or any firmware to 2.3 HOT 1
- Spider 3 with TMC2209 V4.0 (fysetc) stepper drivers HOT 4
- BTT Microprobe Causes board to stop working
- Spider v3 cant run BTT EBB 2209 CAN toolhead (Fysetc Voron 2.4 R2) HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from fysetc-spider.