CLRacing / F7 v2.1 / USER1 Mode missing about emuconfigurator

[orloborlo]

pinio1 is PA14 = pin 49 on F722
i checked directly on the pin and i am getting 3.3 V when User1 is active and 0 volts when User1 is not active.
So it is all OK with the setup, betaflight - which is the bad news = the board is defective.
I followed VTX+ traces to a transistor that has Vbat on one pin....

[Kaiowarez]

Thank you for the clarification., and sorry to hear you got a defective board bro

…

On Fri, Jan 15, 2021, 10:49 PM orloborlo ***@***.***> wrote: pinio1 is PA14 = pin 49 on F722 i checked directly on the pin and i am getting 3.3 V when User1 is active and 0 volts when User1 is not active. So it is all OK with the setup, betaflight - which is the bad news = the board is defective. I followed VTX+ traces to a transistor that has Vbat on one pin.... — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#207 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AOMD72AG7JUGXHTY7MTA4I3S2EEEXANCNFSM4NJ5BQOA> .

[nerdCopter]

@Quick-Flash is this due the user4 vs user1 swap, or does Kaio need to look at target?
Does GUI need change?

[mrrodgers]

I'm having the same issue. using Zeezf7 fc. Needs user 1 mode to turn power on vtx.

[COGNZNT]

Im having the same issue, using Talon F7 Fusion. It also needs user 1 mode to turn power on to the vtx.

[Kaiowarez]

Okay
For all you guys not having video
Check resource PINIO 1 <###>
Make sure it's not none
If it's filled out
Do set pinio_box =39,255,255,255
That should assign your vtx switch to vtx pidmode in modes tab
Then adjust the slider for it to work
Either have it on on-arm or just have the slider encompass the whole range so it's always on
If it's not working or stuff is missing hit me up on discord emuflight I'll try to help you more there
Kaio Pryde

[Kaiowarez]

The talonf7fusion I remade to have the aux setup already I'm just jot sure if it got merged in with the new configurator
Unfortunately I can't do the same for the clracing since the older boards use the same target but didn't have a vtx pid switch built in.. Meaning the vtx is always on on the older boards

[orloborlo]

My CLRacing F7 v2.1 is having similar problem - can not power on VTX with Pit mode and neither User1
diff all
The board has a switch for Real Pit VX on/off...
Any ideas???

# version
# Betaflight / STM32F7X2 (S7X2) 4.2.6 Jan  5 2021 / 19:08:42 (a4b6db1e7) MSP API: 1.43
# config: manufacturer_id: CLRA, board_name: CLRACINGF7, version: 294f73cd, date: 2020-11-05T19:01:48Z

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name CLRACINGF7
manufacturer_id CLRA
mcu_id 002700353438511236383538
signature 

# feature
feature GPS
feature LED_STRIP

# map
map TAER1234

# serial
serial 1 2 115200 57600 0 115200

# led
led 0 0,0::F:11
led 1 1,0::G:0
led 2 2,0::L:0
led 3 3,0::A:0
led 4 4,0::A:0
led 5 5,0::L:0
led 6 6,0::S:0
led 7 7,0::FTW:12

# mode_color
mode_color 3 5 9

# aux
aux 0 0 0 925 1250 0 0
aux 1 1 1 900 1600 0 0
aux 2 2 1 1650 2075 0 0
aux 3 39 3 900 2075 0 0

# master
set gyro_to_use = FIRST
set acc_trim_roll = -2
set acc_calibration = 0,27,-6,1
set mag_hardware = NONE
set baro_hardware = NONE
set min_throttle = 1070
set use_unsynced_pwm = OFF
set motor_pwm_rate = 480
set vbat_scale = 160
set gps_provider = UBLOX
set gps_sbas_mode = AUTO
set gps_auto_baud = ON
set gps_ublox_use_galileo = ON

[Kaiowarez]

Check for resource pinio 1 get pinio and get pinio_box Those are the lines that is needed for users to work