It seems no console on V500.R001.A103.00.G021.B013 about wibox

[theverdu]

Thanks duhow, root/aszeno works for me. Telnet console is not enabled by default and adding the env telnetctrl=1 does not enable it on restart.

But finally i got the mdt0-6 files, i send you by pm and try to continue from there.

Many thanks for your help

[Co1dSUN]

Hello, I have done the same just a couple weeks ago. You have to change tty in u-boot. But I forgot which tty it should be. It has to be one of ttySGK0, ttySGK1 or ttySGK2

…

On Sun, Nov 6, 2022 at 1:49 PM theverdu ***@***.***> wrote: Hi duhow, Thanks for your work on this :-) my goal is to integrate my wibox on HA, but It seems there is no console access on newer firmware versions, nothing appear after init process: [image: image] <https://user-images.githubusercontent.com/93820609/200171094-ab49bac8-2aa9-4e39-b882-f6ab41ac1b7b.png> I can access to U-Boot pressing any key on start, any tip on how to proceed at this point? For other users: to avoid soldering i filed 2mm this connectors with a dremel: [image: image] <https://user-images.githubusercontent.com/93820609/200171406-a743bd9a-7056-4409-9446-eb38927a74d7.png> — Reply to this email directly, view it on GitHub <#14>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AF2J42KJKJACDXUXGCSOWGLWG6SN7ANCNFSM6AAAAAARYNGKBE> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[theverdu]

Wow Co1dSUN, many thanks for your fast response,

setenv consoledev 'ttySGK0'
saveenv
reset

As you say, this makes the login appear when i hit any key, but can't log with the usr/pw provided, it say "user no valid" and continuous message are appearing, do you know if i must disable any output or do something else?

[Co1dSUN]

IDK, I used console only to realize where I do something wrong and why it is not start any more or to upload firmware by u-boot again and again. What firmware version do you have there? You can check it in wibox app.

[duhow]

Thanks for the info @theverdu !
The output you're looking at comes from the Sofia application, not a direct shell.
You can try with adminapp/adminapp2 or root/aszeno ?
I'd be very interested in a full dump of the mtd partitions if you get the chance to have them.

[duhow]

Got the files, while I'll still need to do more investigation:

mtd2 - 1966080 3f630e56a3d31066a38409edac19ab37
Linux kernel ARM boot executable zImage (little-endian)

mtd3 - 2293760 5b9d494a882869f44b340d1a8f18f418
Squashfs filesystem, little endian, version 4.0, xz compressed, 2227342 bytes, 505 inodes, blocksize: 65536 bytes, created: Sun May 22 06:43:56 2022
md5 of 2227342 bytes - 6bc7e845c4fd5afeffa5d1a873c39e9e

mtd4 - 11599872 d56c6b9d948f4216efcdb590cec25ce3
Linux Compressed ROM File System data, little endian size 4235264 version 2 sorted_dirs CRC 0x10606cc5, edition 0, 1756 blocks, 105 files
md5 of 4235264 bytes - b496b8018bf2029a9458893f0f14dd13

• /usr/run.sh now has #telnetd & commented / disabled. Thanks. 😂 (the env telnetctrl=1 is used in other HiSilicon cameras, but does not apply in here)
• New addition to kernel network settings:

echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce

• I see some references in config.lua and Sofia binary: SupportAmazonAlexa = 0

[duhow]

Overall I don't see any differences in the procedure, so you may proceed to install the patch as defined in the guide.

[duhow]

Due to a bad re-soldering process I did, apparently I've cut RX pin, so now I have an isolated board. 🥲
I face some issues with B013, if Sofia does not run (that triggers some other process?), the board will stop the Wifi.
RTL871X: CardDisableRTL8188FU.

Currently investigating this. Any feedback is welcome :)

[duhow]

Found the issue...
Sofia won't load Wifi settings from a normal wpa_supplicant.conf file, and if the file does not exist in /mnt/mtd/wpa_supplicant.conf, then the board won't connect to the Wireless AP, which explains all the other behaviors. I'll add more details and fixes for this.

[duhow]

Added bbfdfad .
Since we already found how to get the console access and so, I'm resolving this issue.