no multicast traffic with following conf (help please) about mumudvb

[braice]

Hello

You are dumping on the IP address of your ethernet card but you route
multicast on the lo (still the SAP seems to be seen) and you are using
special multicast adresses 239.255

is there a reason for that ?

6.1 http://tools.ietf.org/html/rfc2365#section-6.1. The IPv4 Local
Scope -- 239.255.0.0/16

239.255.0.0/16 is defined to be the IPv4 Local Scope. The Local
Scope is the minimal enclosing scope, and hence is not further
divisible. Although the exact extent of a Local Scope is site
dependent, locally scoped regions must obey certain topological
constraints. In particular, a Local Scope must not span any other
scope boundary. Further, a Local Scope must be completely contained
within or equal to any larger scope. In the event that scope regions
overlap in area, the area of overlap must be in its own local scope.
This implies that any scope boundary is also a boundary for the Local
Scope. The more general topological requirements for administratively
scoped regions are discussed below.

2014-05-10 10:05 GMT+02:00 ovidiu [email protected]:

with full autoconfig i have multicast traffic but channels are having
bottlenecks
with partial config when i tcpdump for check traffic i got no multicast
packets just
root@debian:~# tcpdump -n host 192.168.50.2
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes
02:53:59.806751 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
2881423504:2881423700, ack 1650496469, win 148, length 196
02:53:59.853052 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
196, win 256, length 0
02:54:00.807875 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
196:472, ack 1, win 148, length 276
02:54:01.054256 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
472, win 255, length 0
02:54:01.325682 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [P.], seq
2940033849:2940034320, ack 1531971463, win 16425, length 471
02:54:01.325704 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [.], ack
471, win 330, length 0
02:54:01.425955 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [P.], seq
1:1255, ack 471, win 330, length 1254
02:54:01.666682 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [.], ack
1255, win 16111, length 0
02:54:01.808963 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
472:1164, ack 1, win 148, length 692
02:54:02.055668 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
1164, win 252, length 0
02:54:02.810003 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
1164:1408, ack 1, win 148, length 244
02:54:03.056578 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
1408, win 251, length 0
02:54:03.326481 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [P.], seq
471:942, ack 1255, win 16111, length 471
02:54:03.326503 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [.], ack
942, win 330, length 0
02:54:03.426732 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [P.], seq
1255:2344, ack 942, win 330, length 1089
02:54:03.667909 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [.], ack
2344, win 16425, length 0
02:54:03.811075 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
1408:2084, ack 1, win 148, length 676
02:54:04.057423 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
2084, win 256, length 0
02:54:04.812114 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
2084:2344, ack 1, win 148, length 260
02:54:05.058459 IP 5.13.13.115.50203 > 192.168.50.2.22: Flags [.], ack
2344, win 255, length 0
02:54:05.327108 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [P.], seq
942:1413, ack 2344, win 16425, length 471
02:54:05.327130 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [.], ack
1413, win 330, length 0
02:54:05.427367 IP 192.168.50.2.8888 > 5.13.13.115.50483: Flags [P.], seq
2344:3263, ack 1413, win 330, length 919
02:54:05.667152 IP 5.13.13.115.50483 > 192.168.50.2.8888: Flags [.], ack
3263, win 16195, length 0
02:54:05.813173 IP 192.168.50.2.22 > 5.13.13.115.50203: Flags [P.], seq
2344:3020, ack 1, win 148, length 676
02:54:05.997797 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 246
02:54:05.997807 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 242
02:54:05.997819 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 242
02:54:05.997823 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 239
02:54:05.997827 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 244
02:54:05.997831 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 242
02:54:05.997835 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 243
02:54:05.997838 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 242
02:54:05.997841 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 241
02:54:05.997850 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 242
02:54:05.997853 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 243
02:54:05.997857 IP 192.168.50.2.53388 > 224.2.127.254.9875: UDP, length 243

routing table is set ok i think

root@debian:~# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.50.1 0.0.0.0 UG 0 0 0 eth0
192.168.50.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
224.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 lo
239.255.0.0 0.0.0.0 255.255.255.0 U 0 0 0 lo
239.255.1.0 0.0.0.0 255.255.255.0 U 0 0 0 lo

CONF used

#------------ TUNING -------------
card=0
#The Transponder frequency
freq=12092
#The polarisation (can be h, v, l, r)
pol=h
#The symbol rate
srate=28000
#the FEC
coderate=7/8
#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the
defined channels)
autoconfiguration=partial
#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234

#Do we need to change the default multicast TTL (if you have routers,
default value : 2) ?
#multicast_iface4=eth0
multicast_ttl=10

#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1

#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
sap_organisation=my_organisation
#The intervall between the SAP announces in second (default 5)
sap_interval=10
---------- PAT REWRITING ----------

#If some of the clients are set top boxes we will probably need to rewrite
the PAT pid
#rewrite_pat=1

---------- SCRAMBLED CHANNELS ----------

#Do we want hadware descrambling ?
#cam_support=1
scam_support=1
ring_buffer_default_size=32768
decsa_default_delay=500000
send_default_delay=1500000
#If you have multiple CAMs you can specify the number of the one wich will
be used
#cam_number=2
----------------------- THE CHANNELS ---------------------

#Configuration for 12 channels
#Channel number : 0
ip=239.255.0.0
port=1234
name=Mooz Dance HD
service_id=11001
pids=5001 5101 5201
#Channel number : 1
ip=239.255.0.1
port=1234
name=AXN White
cam_pmt_pid=5002
service_id=11002
pids=5002 5102 5202 5302 5402 5502 5602 5702 5802 5902
oscam=1
#Channel number : 2
ip=239.255.0.2
port=1234
name=AXN Black
cam_pmt_pid=5003
service_id=11003
pids=5003 5103 5203 5303 5403 5503 5603 5703 5803 5903
oscam=1
#Channel number : 3
ip=239.255.0.3
port=1234
name=AXN CE
cam_pmt_pid=5004
service_id=11004
pids=5004 5104 5204 5304 5404 5604 5704
oscam=1
#Channel number : 4
ip=239.255.0.4
port=1234
name=AXN Romania
cam_pmt_pid=5005
service_id=11005
pids=5005 5105 5205 5305 5405
oscam=1
#Channel number : 5
ip=239.255.0.5
port=1234
name=AXN Czech
cam_pmt_pid=5006
service_id=11006
pids=5006 5106 5206 5306
oscam=1
#Channel number : 6
ip=239.255.0.6
port=1234
name=Mooz Dance
service_id=11007
pids=5007 5107 5207
#Channel number : 7
ip=239.255.0.7
port=1234
name=Inedit TV
service_id=11008
pids=5008 5108 5208
#Channel number : 8
ip=239.255.0.8
port=1234
name=TVSudEst
service_id=11009
pids=5009 5109 5209
#Channel number : 9
ip=239.255.0.9
port=1234
name=Mynele TV
service_id=11010
pids=5010 5110 5210
#Channel number : 10
ip=239.255.0.10
port=1234
name=TV Sonce
service_id=11011
pids=5011 5111 5211
#Channel number : 11
ip=239.255.0.11
port=1234
name=TV Sutel
service_id=11013
pids=5013 5113 5213
#End of config file

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/63
.

[ovidiu31]

Bonjour Braice

Yes im using 239.255 class ip's because the QAM modulator which im using doesn't allow me to use another type of ip addresses.
Could you please advise in this specific case how should i setup multicast routes?

at this moment in rc.local i have

ifconfig lo multicast
ip route add 239.255.0.0/24 dev lo src 127.0.0.1
ip route add 239.255.1.0/24 dev lo src 127.0.0.1
ip route flush cache

Should be different?

With full autoconfig i have DVR buffer overrun errors

[braice]

Ok some more question

How your cam modulated is connected ? it seems that you send the multicast
trafic on the lo interface, is that what you really want ?
You can say to MuMuDVB which interface send the multicast traffic to, see
the readme_conf

You can also use iptraf to see the amount of traffic on each interface.

Concerning DVR error, try to increase DVR buffer size.

Best regards

2014-05-11 9:26 GMT+02:00 ovidiu [email protected]:

Bonjour Braice

Yes im using 239.255 class ip's because the QAM modulator which im using
doesn't allow me to use another type of ip addresses.
Could you please advise in this specific case how should i setup multicast
routes?

at this moment in rc.local i have

ifconfig lo multicast
ip route add 239.255.0.0/24 dev lo src 127.0.0.1
ip route add 239.255.1.0/24 dev lo src 127.0.0.1
ip route flush cache

Should be different?

With full autoconfig i have DVR buffer overrun errors

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/63#issuecomment-42764074
.

[ovidiu31]

Thank you for reading and helping out Braice.

So the equation is simple , i have

1. system (pc) with a dual tunner pcie (TBS) and 1 eth0 gigabit interface (192.168.50.2)
2. router TP Link gigabit (multicast capable) (192.168.50.1)
3. qam modulator (gigabit) (192.168.50.3) (multicast ip class 239.x.x.x only)

I can use a direct conection pc -> qam modulator with a cross cable to eliminate de router and to have clean gigabit badwidth between pc and qam.

What i need Braice is 2 example conf files for tuner 1 and tuner 2 with some exact parameters to be able to broadcast at least 5 channels from one tuner (freq 12092 V thor 1W) and 5 channels from second tuner(freq 11938 H thor 1w) without bottlenecks.

I mean im able to do this but for some reason i have some bottlenecks and streams are not working fine ( i have signal quality 96%) so imo the problem is networking related , mostlikely because of the huge traffic generated by multicast.

how much can i increase the buffer size?
eliminating the router could be a helpfull thing?
is there any other specific option in the conf file that can help to optimise the multicast traffic and avoid bottlenecks?

Thank you

[braice]

Hello

try anything but 239.255 like 239.100

Also route the multicast on the eth0 interface

For DVR buffer see
http://www.mumudvb.net/doc/mumudvb-2.0.0/README_CONF.html#_various_parameters
dvr_buffer_size option

I'll provide you example files tomorrow but meanwhile I hope these few
advises will be helpful

Best

2014-05-11 17:23 GMT+02:00 ovidiu [email protected]:

Thank you for reading and helping out Braice.

So the equation is simple , i have

1. system (pc) with a dual tunner pcie (TBS) and 1 eth0 gigabit interface
   (192.168.50.2)
2. router TP Link gigabit (multicast capable) (192.168.50.1)
3. qam modulator (gigabit) (192.168.50.3) (multicast ip class 239.x.x.x
   only)

I can use a direct conection pc -> qam modulator with a cross cable to
eliminate de router and to have clean gigabit badwidth between pc and qam.

What i need Braice is 2 example conf files for tuner 1 and tuner 2 with
some exact parameters to be able to broadcast at least 5 channels from one
tuner (freq 12092 V thor 1W) and 5 channels from second tuner(freq 11938 H
thor 1w) without bottlenecks.

I mean im able to do this but for some reason i have some bottlenecks and
streams are not working fine ( i have signal quality 96%) so imo the
problem is networking related , mostlikely because of the huge traffic
generated by multicast.

how much can i increase the buffer size?
eliminating the router could be a helpfull thing?
is there any other specific option in the conf file that can help to
optimise the multicast traffic and avoid bottlenecks?

Thank you

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/63#issuecomment-42773446
.

[braice]

Some news on this issue ?

2014-05-11 23:01 GMT+02:00 Brice Dubost [email protected]:

Hello

try anything but 239.255 like 239.100

Also route the multicast on the eth0 interface

For DVR buffer see

http://www.mumudvb.net/doc/mumudvb-2.0.0/README_CONF.html#_various_parameters
dvr_buffer_size option

I'll provide you example files tomorrow but meanwhile I hope these few
advises will be helpful

Best

2014-05-11 17:23 GMT+02:00 ovidiu [email protected]:

Thank you for reading and helping out Braice.

So the equation is simple , i have

1. system (pc) with a dual tunner pcie (TBS) and 1 eth0 gigabit interface
   (192.168.50.2)
2. router TP Link gigabit (multicast capable) (192.168.50.1)
3. qam modulator (gigabit) (192.168.50.3) (multicast ip class 239.x.x.x
   only)

I can use a direct conection pc -> qam modulator with a cross cable to
eliminate de router and to have clean gigabit badwidth between pc and qam.

What i need Braice is 2 example conf files for tuner 1 and tuner 2 with
some exact parameters to be able to broadcast at least 5 channels from one
tuner (freq 12092 V thor 1W) and 5 channels from second tuner(freq 11938 H
thor 1w) without bottlenecks.

I mean im able to do this but for some reason i have some bottlenecks and
streams are not working fine ( i have signal quality 96%) so imo the
problem is networking related , mostlikely because of the huge traffic
generated by multicast.

how much can i increase the buffer size?
eliminating the router could be a helpfull thing?
is there any other specific option in the conf file that can help to
optimise the multicast traffic and avoid bottlenecks?

Thank you

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/63#issuecomment-42773446
.

[ovidiu31]

Bonjour Braice

Please have a look to these 2 configs and tell me please if something wrong
asking because if i set parameter multicast_iface4=eth0 starting to receive buffer run errors not matter how big is the DVR buffer set.
At the moment is stabilised with full auto config but i would like to choose some specific channels only to be multicasted not all the channels from transponder.

Thank you

CONFIG 1
#------------ TUNING -------------
card=1
#The Transponder frequency
freq=12265
#The polarisation (can be h, v, l, r)
pol=V
#The symbol rate
srate=28000
#the FEC
#coderate=7/8
#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the defined channels)
autoconfiguration=partial

#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234

#Do we need to change the default multicast TTL (if you have routers, default value : 2) ?
multicast_ttl=10
multicast_iface4=eth0

#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1

#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
#sap_organisation=my_organisation
#The intervall between the SAP announces in second (default 5)
#sap_interval=10

---------- PAT REWRITING ----------

#If some of the clients are set top boxes we will probably need to rewrite the PAT pid
#rewrite_pat=1

---------- SCRAMBLED CHANNELS ----------

#Do we want hadware descrambling ?
#cam_support=1
scam_support=1
ring_buffer_default_size=32768
decsa_default_delay=500000
send_default_delay=1500000
#If you have multiple CAMs you can specify the number of the one wich will be used
#cam_number=2

----------------------- THE CHANNELS ---------------------

#End of global part

#Configuration for 16 channels
#Channel number : 0
ip=239.255.1.0
port=1234
name=Eurosport
cam_pmt_pid=100
service_id=30901
pids=100 101 110 111 112 113 120
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 1
ip=239.255.1.1
port=1234
name=MTV Music
cam_pmt_pid=150
service_id=30902
pids=150 151 162
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 2
ip=239.255.1.2
port=1234
name=Discovery Channel
cam_pmt_pid=200
service_id=30903
pids=200 201 210 211 212
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 3
ip=239.255.1.3
port=1234
name=Viasat Explorer
cam_pmt_pid=250
service_id=30904
pids=250 251 259 261 262 273
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 4
ip=239.255.1.4
port=1234
name=CBS Reality
cam_pmt_pid=300
service_id=30905
pids=300 301 310 311 312
#Channel number : 5
ip=239.255.1.5
port=1234
name=Test
cam_pmt_pid=350
service_id=30906
pids=350 351 360 361 362 363
#Channel number : 6
ip=239.255.1.6
port=1234
name=SuperTV2
cam_pmt_pid=400
service_id=30907
pids=400 401 410
#Channel number : 7
ip=239.255.1.7
port=1234
name=National Geographic RO
cam_pmt_pid=450
service_id=30908
pids=450 451 463 473
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 8
ip=239.255.1.8
port=1234
name=Daring!TV
cam_pmt_pid=500
service_id=30909
pids=500 501 512
#Channel number : 9
ip=239.255.1.9
port=1234
name=Pro TV
cam_pmt_pid=550
service_id=30910
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 10
ip=239.255.1.10
port=1234
name=Sport5
cam_pmt_pid=600
service_id=30911
pids=600 601 611
#Channel number : 11
ip=239.255.1.11
port=1234
name=FEM3
cam_pmt_pid=650
service_id=30912
pids=650 651 660
#Channel number : 12
ip=239.255.1.12
port=1234
name=JOJ Plus
cam_pmt_pid=700
service_id=30913
pids=700 701 714
#Channel number : 13
ip=239.255.1.13
port=1234
name=Cinemax2
cam_pmt_pid=750
service_id=30914
pids=750 751 760 761 762 763 770 771 772 773
#Channel number : 14
ip=239.255.1.14
port=1234
name=Duna TV
cam_pmt_pid=800
service_id=30916
pids=800 801 810 820
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 15
ip=239.255.1.15
port=1234
name=Pro TV International
cam_pmt_pid=850
service_id=30917
pids=850 851 863
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#End of config file

CONFIG 2

#------------ TUNING -------------
card=0
#The Transponder frequency
freq=11727
#The polarisation (can be h, v, l, r)
pol=V
#The symbol rate
srate=28000
#the FEC
coderate=7/8
#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the defined channels)
autoconfiguration=partial

#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234
multicast_ipv4=1
#multicast_iface4=eth0
multicast_ttl=2
#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1

#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
#sap_organisation=my_organisation
#The intervall between the SAP announces in second (default 5)
#sap_interval=10

---------- PAT REWRITING ----------

#If some of the clients are set top boxes we will probably need to rewrite the PAT pid
#rewrite_pat=1

---------- SCRAMBLED CHANNELS ----------

#Do we want hadware descrambling ?
#cam_support=1
scam_support=1
ring_buffer_default_size=32768
decsa_default_delay=500000
send_default_delay=1500000
#If you have multiple CAMs you can specify the number of the one wich will be used
#cam_number=2

----------------------- THE CHANNELS ---------------------

#Configuration for 18 channels
#Channel number : 7
ip=239.255.0.7
port=1234
name=HBO
cam_pmt_pid=100
service_id=30101
pids=100 101 110 112 119 120
oscam=1
#Channel number : 8
ip=239.255.0.8
port=1234
name=NOVA Cinema
cam_pmt_pid=150
service_id=30102
pids=150 151 161 170
#Channel number : 10
ip=239.255.0.10
port=1234
name=Sport1
cam_pmt_pid=250
service_id=30104
pids=250 251 260
oscam=1
#Channel number : 11
ip=239.255.0.11
port=1234
name=CT1
cam_pmt_pid=350
service_id=30106
pids=350 351 361 370
#Channel number : 12
ip=239.255.0.12
port=1234
name=TV Markiza
cam_pmt_pid=400
service_id=30107
pids=400 401 414 420
#Channel number : 13
ip=239.255.0.13
port=1234
name=TA3
cam_pmt_pid=450
service_id=30108
pids=450 451 464
#Channel number : 14
ip=239.255.0.14
port=1234
name=Prima TV
cam_pmt_pid=500
service_id=30109
pids=500 501 511 520
oscam=1
#Channel number : 17
ip=239.255.0.17
port=1234
name=TV Paprika
cam_pmt_pid=650
service_id=30112
pids=650 651 660 661 670
oscam=1
#End of config file

[braice]

Hello
why not using autoconf_sid_list to choose you channel

Also, is it working with channels in clear (without oscam) ?

Just to see if it is an oscam issue.

Best

2014-05-18 8:33 GMT+02:00 ovidiu [email protected]:

Bonjour Braice

Please have a look to these 2 configs and tell me please if something
wrong
asking because if i set parameter multicast_iface4=eth0 starting to
receive buffer run errors not matter how big is the DVR buffer set.
At the moment is stabilised with full auto config but i would like to
choose some specific channels only to be multicasted not all the channels
from transponder.

Thank you

CONFIG 1
#------------ TUNING -------------
card=1
#The Transponder frequency
freq=12265

#The polarisation (can be h, v, l, r)
pol=V

#The symbol rate
srate=28000
#the FEC
#coderate=7/8

#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the
defined channels)
autoconfiguration=partial

#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234

#Do we need to change the default multicast TTL (if you have routers,
default value : 2) ?
multicast_ttl=10
multicast_iface4=eth0

#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1

#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
#sap_organisation=my_organisation

#The intervall between the SAP announces in second (default 5)
#sap_interval=10

---------- PAT REWRITING ----------

#If some of the clients are set top boxes we will probably need to rewrite
the PAT pid
#rewrite_pat=1

---------- SCRAMBLED CHANNELS ----------

#Do we want hadware descrambling ?
#cam_support=1
scam_support=1
ring_buffer_default_size=32768
decsa_default_delay=500000
send_default_delay=1500000
#If you have multiple CAMs you can specify the number of the one wich will
be used
#cam_number=2
----------------------- THE CHANNELS ---------------------

#End of global part

#Configuration for 16 channels
#Channel number : 0
ip=239.255.1.0
port=1234
name=Eurosport
cam_pmt_pid=100
service_id=30901
pids=100 101 110 111 112 113 120
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 1
ip=239.255.1.1
port=1234
name=MTV Music
cam_pmt_pid=150
service_id=30902
pids=150 151 162
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 2
ip=239.255.1.2
port=1234
name=Discovery Channel
cam_pmt_pid=200
service_id=30903
pids=200 201 210 211 212
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 3
ip=239.255.1.3
port=1234
name=Viasat Explorer
cam_pmt_pid=250
service_id=30904
pids=250 251 259 261 262 273
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 4
ip=239.255.1.4
port=1234
name=CBS Reality
cam_pmt_pid=300
service_id=30905
pids=300 301 310 311 312
#Channel number : 5
ip=239.255.1.5
port=1234
name=Test
cam_pmt_pid=350
service_id=30906
pids=350 351 360 361 362 363
#Channel number : 6
ip=239.255.1.6
port=1234
name=SuperTV2
cam_pmt_pid=400
service_id=30907
pids=400 401 410
#Channel number : 7
ip=239.255.1.7
port=1234
name=National Geographic RO
cam_pmt_pid=450
service_id=30908
pids=450 451 463 473
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 8
ip=239.255.1.8
port=1234
name=Daring!TV
cam_pmt_pid=500
service_id=30909
pids=500 501 512
#Channel number : 9
ip=239.255.1.9
port=1234
name=Pro TV
cam_pmt_pid=550
service_id=30910
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 10
ip=239.255.1.10
port=1234
name=Sport5
cam_pmt_pid=600
service_id=30911
pids=600 601 611
#Channel number : 11
ip=239.255.1.11
port=1234
name=FEM3
cam_pmt_pid=650
service_id=30912
pids=650 651 660
#Channel number : 12
ip=239.255.1.12
port=1234
name=JOJ Plus
cam_pmt_pid=700
service_id=30913
pids=700 701 714
#Channel number : 13
ip=239.255.1.13
port=1234
name=Cinemax2
cam_pmt_pid=750
service_id=30914
pids=750 751 760 761 762 763 770 771 772 773
#Channel number : 14
ip=239.255.1.14
port=1234
name=Duna TV
cam_pmt_pid=800
service_id=30916
pids=800 801 810 820
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#Channel number : 15
ip=239.255.1.15
port=1234
name=Pro TV International
cam_pmt_pid=850
service_id=30917
pids=850 851 863
oscam=1
ring_buffer_size=32768
decsa_delay=1500000
send_delay=2500000
#End of config file

CONFIG 2

#------------ TUNING -------------
card=0
#The Transponder frequency
freq=11727

#The polarisation (can be h, v, l, r)
pol=V

#The symbol rate
srate=28000
#the FEC
coderate=7/8
#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the
defined channels)
autoconfiguration=partial

#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234
multicast_ipv4=1
#multicast_iface4=eth0
multicast_ttl=2

#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1

#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
#sap_organisation=my_organisation

#The intervall between the SAP announces in second (default 5)
#sap_interval=10

---------- PAT REWRITING ----------

#If some of the clients are set top boxes we will probably need to rewrite
the PAT pid
#rewrite_pat=1

---------- SCRAMBLED CHANNELS ----------

#Do we want hadware descrambling ?
#cam_support=1
scam_support=1
ring_buffer_default_size=32768
decsa_default_delay=500000
send_default_delay=1500000
#If you have multiple CAMs you can specify the number of the one wich will
be used
#cam_number=2
----------------------- THE CHANNELS ---------------------

#Configuration for 18 channels

#Channel number : 7
ip=239.255.0.7
port=1234
name=HBO
cam_pmt_pid=100
service_id=30101
pids=100 101 110 112 119 120
oscam=1

#Channel number : 8
ip=239.255.0.8
port=1234
name=NOVA Cinema
cam_pmt_pid=150
service_id=30102
pids=150 151 161 170

#Channel number : 10
ip=239.255.0.10
port=1234
name=Sport1
cam_pmt_pid=250
service_id=30104
pids=250 251 260
oscam=1

#Channel number : 11
ip=239.255.0.11
port=1234
name=CT1
cam_pmt_pid=350
service_id=30106
pids=350 351 361 370
#Channel number : 12
ip=239.255.0.12
port=1234
name=TV Markiza
cam_pmt_pid=400
service_id=30107
pids=400 401 414 420
#Channel number : 13
ip=239.255.0.13
port=1234
name=TA3
cam_pmt_pid=450
service_id=30108
pids=450 451 464
#Channel number : 14
ip=239.255.0.14
port=1234
name=Prima TV
cam_pmt_pid=500
service_id=30109
pids=500 501 511 520
oscam=1
#Channel number : 17
ip=239.255.0.17
port=1234
name=TV Paprika
cam_pmt_pid=650
service_id=30112
pids=650 651 660 661 670
oscam=1
#End of config file

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/63#issuecomment-43432667
.

[ovidiu31]

in Clear Cam everything seems to work ok no issues.

Can you please be more specific of how to use parameter :
autoconf_sid_list to choose specific channels from a transponder.

[braice]

If you want the channels with service IDs 304 598 and 1345 just do

autoconf_sid_list=304 598 1345
autoconf=full

Best regards

2014-05-26 11:10 GMT+02:00 ovidiu [email protected]:

in Clear Cam everything seems to work ok no issues.

Can you please be more specific of how to use parameter :
autoconf_sid_list to choose specific channels from a transponder.

—
Reply to this email directly or view it on GitHub
https://github.com/braice/MuMuDVB/issues/63#issuecomment-44171199.

[ovidiu31]

braice close this as it is solved.

[braice]

closed

2014-08-03 10:24 GMT+02:00 ovidiu [email protected]:

braice close this as it is solved.

—
Reply to this email directly or view it on GitHub
https://github.com/braice/MuMuDVB/issues/63#issuecomment-50984954.